Re: J2320 - V12.4 BGP And Firewall Setup
Hi, Ok so BGP has come up and i`m seeing active routes in the table but i cannot get any traffic to pass through the router itself e.g. ping or see any devices at either end. I have at the moment set...
View ArticleRe: Two Networks Config
i'm in /var/db/ root@sw1:RE:0% cd /var/db/root@sw1:RE:0% ls -latotal 40drwxr-xr-x 5 root wheel 512 Sep 5 02:00 .drwxr-xr-x 31 root wheel 512 Nov 15 2011 ..drwxr-xr-x 5 root wheel 512 Nov 15 2011...
View ArticleRe: J2320 - V12.4 BGP And Firewall Setup
The two things to check then are to confirm that sessions are being accepted and created for your traffic. Setup the ping and then use: show security flow session source-prefix 1.1.1.1...
View ArticleRe: MX480 IP SLA ??
hmmm... suprisingly the simple IP SLA feature cant find on MX serious. is there any road map the MX will support the IP SLA similiar feature ?
View ArticleSupport for 1Gbps SFP in MIC3-3D-10XGE-SFPP?
Does anyone know if the MIC3-3D-10XGE-SFPP card supports 1Gbps SFP's?I know there is the MIC-3D-20GE-SFP for that but since we are migrating from 1Gbps to 10Gbps I'd like the MIC to supprt both speeds.
View ArticleRe: Support for 1Gbps SFP in MIC3-3D-10XGE-SFPP?
MIC3-3D-10XGE-SFPP is 10G / SFP+ only.
View ArticleRe: J2320 - V12.4 BGP And Firewall Setup
Hi, Stil not having much luck.... I have setup a pair of J2320`s running V12 firmware, configured BGP between them (to simulate the MPLS proviers end) and i can see those routes replicating between the...
View ArticleRe: Support for 1Gbps SFP in MIC3-3D-10XGE-SFPP?
Hi, This MIC has 10 Gig posrts only and 1G SFPs can not be used.You can follow below links for more detail about this mic. 10-Gigabit Ethernet MIC with SFP+ (10 Ports) [KUDOS PLEASE! If you think I...
View ArticleRe: Duplicate Frame route issue in 16.1R4 for BNG
Functionality is broken is next generation subscriber management release.Please note this will be available in later releases.
View ArticleRe: Two Networks Config
Hey, Can you try deleting the existing config directory in /var/db and recreate and check if it works? root@:RE:0%root@:RE:0% rm config/rm: config/: is a directoryroot@:RE:0% rm -r config/root@:RE:0%...
View ArticleRe: J2320 - V12.4 BGP And Firewall Setup
Securiity policies that permit the traffic are needed in the direction of the initiator (from-zone) of the traffic to the destination (to-zone) set security policy from-zone NAME to-zone NAME Both SRX...
View ArticleL2_BRIDGE family extension message
MX480 with 15.1F7I'm migrating irb interfaces from one OSPF routing-instance to another. This only changes the interface unit from ae5.3 to ae5.128. I keep getting this error for every irb (one for...
View ArticleRe: L2_BRIDGE family extension message
Hi, Can you please share below : >show interface ae5.3
View ArticleNeed Help : OSPFv3 issue on Juniper MP-BGP --> OSPF
I am currently using OSPFv3 between the CE and PE in the following scenario. The PEs are Juniper and CEs, another vendor (Cisco). I have enabled the address families/realms for both IPv4 and IPv6...
View Article100Mb SFP on ACX5048
Hi, I know that this can support 1Gb SFPs, but has anyone managed to test whether you can use a copper SFP and connect a device at 100Mb?Will the ACS5048 support 100Mb F/D speeds using a 1Gb copper...
View ArticleRe: 100Mb SFP on ACX5048
Hi, mskipsey! I don't personally have the ACX 5048 but reviewing the ACX 5000 series documentation it does not appear so. Here are the relevant portions of the document. All 48 of these ports can be...
View ArticleRe: 100Mb SFP on ACX5048
I can confirm that 100 Mbps optics are not supported on ACX5048 - with Junos 17.3R1 the smaller platform now supports for 100 Mbps but a bit strange that it wasn't a focus for ACX5000. HardwareSupport...
View ArticleRe: 100Mb SFP on ACX5048
Interesting find, as that does appear to confirm that the other ACX platforms now do support 100Mb optics, but not the 5000 series....
View ArticleRe: L2_BRIDGE family extension message
OK. What are you looking for? > show interfaces ae5.3 detail Logical interface ae5.3 (Index 461) (SNMP ifIndex 693) (Generation 401) Description: intgway routes Flags: Up SNMP-Traps 0x4000 VLAN-Tag...
View ArticleRe: Need Help : OSPFv3 issue on Juniper MP-BGP --> OSPF
Hi, Can you please share the export/import policy which you are using to advertise BGP routes to OSPFv3 here? Thanks
View Article