Re: IPSEC with NAT to non RCF Address on Phase 2
When you say not using RFC1918 within the tunnel, do you mean you are using a route based VPN utilising st0 interfaces and these must not be RFC1918 addresses?
View ArticleMS-MIC
Dears, Does any one exactly know what are the services that MS-MIC is providing? and the required license accordingly? as i couldn't able to understand the combination between the the MS-MIC, Service...
View ArticleRe: MS-MIC
Hi Hamdy,You may want to go through the below link to understand the MIC card and the services offered;http://www.juniper.net/documentation/en_US/junos15.1/topics/concept/ms-mic-and-mpc-overview.html I...
View ArticleRe: MS-MIC
Hi, Ms-Mic supports services like JFLOW,IPSEC,IDS,RPM,SFW,CG-NAT,SIP,NAT44/64 etc. Two types of Ms-Mic logical interfaces can be found, one interface is Sp-* and other interface type is ms-*. Mx...
View ArticleRe: About Junos BGP
Hi, Juniper has native support for Ipv6 for Mx. If you are running Srx code base then you might have to enable is specifially. What product / Junos are you using ? Can you see the Direct Interface...
View ArticleRe: MS-MIC
Hello,SP- interfaces are hosted by MS-PIC, AS-PIC (EOL) or MS-DPC, not MS-MIC nor MS-MPC.MS-PIC and AS-PIC are for M-series or T-series routers.MS-DPC is only for MX240/480/960.MS-MIC goes into...
View ArticleL3vpn
Hi , Please help me to understand the following: why routing protocol is defined under instance in L3vpn and why not define globally????>>>set routing instance site-1 protocol bgp group EBGP...
View ArticleRe: L3vpn
"why routing protocol is defined under instance in L3vpn and why not define globally????" The reason is that every route learned from the CE has to go into the vrf-table (<vrf-name>.inet.0) and...
View ArticleRe: L3vpn
As Alexander notes, the architecture here is to keep the ce specific routing protocols into the routing instance while the global or signaling protocols are in the root or base routing instance. For a...
View ArticleRe: DPCE 20x 1GE + 2x 10GE R Issue
Also without tunnel config the issue continue.I'll swap the board ASAP
View ArticleIs it possible to set an mpls based layer3 vpn on my mx 960 router?
Hi junos guys ,I need to link my mx960 with a cisco router as a PE using a mpls based l3 vpn.Two days ago a begin searching for some application exaples without success ... Im afraid my router does not...
View ArticleRe: OSPF routing problem
Thank you for this. I was thinking that this would be the case but hoping I was missing something that might enable the 172.40 vlan to be routed across without trunk links or a physical connection.
View ArticleRe: Explaination on traceroute
http://www.juniper.net/documentation/en_US/junos13.3/topics/concept/policy-per-packet-load-balancing-overview.htmlhttp://www.juniper.net/techpubs/en_US/junos12.3/topics/concept/policy-per-packet-load-b...
View ArticleRe: L3vpn
Hi Alex, Thank your for your answer. But the confusion is now between data traffic and control plane traffic.Since the CE interface is defined under routing instance, the routing updates we get on CE...
View ArticleRe: L3vpn
Hi, There are two ways you have to look at this 1. traffic till ce - pe2. traffic after reaching Pe traffic be it be control plane or data plane as you have righly put will land on PE device VRF...
View ArticleRe: L3vpn
Hi Rakesh, Thank you so much for sharing your views. ________ ge0/0/1 ___________ | CE |------------ | PE | ------------- ___________...
View ArticleNot receiving netflow v9, v5 works.
Hi, We have an ELK environment running that gathers data and processes it to the point where end users can visualize the data and such. Right now we're dealing with Syslogs and Netflow, but are...
View ArticleRe: Not receiving netflow v9, v5 works.
pls check below URLyou may get some help http://www.juniper.net/documentation/en_US/junos12.1x46/topics/task/configuration/services-version-9-flow-template-flow-aggregation-configuring.html
View ArticleMX-104 bgp neighbor go down -strange behavior-
Hi all, We have a MX-104, with the following OS: Model: mx104Junos: 13.3R7.4JUNOS Base OS boot [13.3R7.4] In BGP configuration, there was only one BGP group, and inside this group, 2 neighbors (i-BGP,...
View ArticleRe: IPSEC with NAT to non RCF Address on Phase 2
perhaps https://tools.ietf.org/html/rfc6598 ?
View Article