Re: Default route question
@Ashvin BGP can only introduce detination based routes to their neighbors. There are lots of tools like communities that you mention to make the distribution of more specific routes scripted and...
View ArticleRe: Default route question
Hi Steve, Agree for BGP which is what I also said in Message 12.However, from what I understand the requirement is for destination/source-based routing but with the list of addresses to be dynamic and...
View ArticleRe: Reg : IOS to JUNOS conversion
Hi, Had few observations with regards to the output:1. I believe the announcement is for IP Transit and can see some prefixes with longer than /24. As a best practice, it is recommended not to...
View ArticleRe: How much firewall filter (ACLs) MX80 & MX240 can handle
Hi, I can confirm that the command works on MX5 root@MX5-R2002> show chassis hardware detail Hardware inventory: Item Version Part number Serial number Description Chassis MX5-Troot@MX5-R2002>...
View ArticleRe: Reg : IOS to JUNOS conversion
Dear Ashvin, Thanks for the input , Based on your input i have created a template for changing the existing configuration . I am planning to remove the existing bgp configuration...
View ArticleMX 480 randomly dropping traffic.
Hi Team,One of our routers MX 480 has been misbehaving for the past two days... it just drops connections and clients connected to the router can't even ping their GW IPs which are defined on the MX...
View ArticleRe: MX 480 randomly dropping traffic.
Hi, One thing that comes to mind is ddos-protection.Could you check:show ddos-protection protocols [icmp | bgp]show ddos-protection protocols statistics terseshow ddos-protection statisticsJust in case...
View ArticleRe: Reg : IOS to JUNOS conversion
Hi, The config template looks ok.Based on the topology, I am not sure if you have any BGP routes that need to be announced to transits, so below term may not be matched:set policy-options...
View ArticleNSSA area-range command
Hello, I have a question regarding the difference between commands. For example, i setup a network with 3 areas. (area 1)<->(area 0)<>(area 2) Area 1 = nssa area with an abr going to area...
View ArticleRe: NSSA area-range command
set protocols ospf area 0.0.0.1 nssa area-range 100.0.0.0/24 Area range command under NSSA Stanza summarizes Type 7 LSA's before getting translated as Type 5 LSA's set protocols ospf area 0.0.0.1...
View ArticleRe: NSSA area-range command
So the behavior that was observed in your box is as per expectation (Inter-area prefixes got summarized afterarea-range is configured under area area-number stanza. area-range under nssa stanza is...
View ArticleRe: NSSA area-range command
I treid it out on my lab and it worked the way you stated. I just couldn't find anything online that pointed out the difference. I think i was looking in the wrong areas online. I appreciate the help...
View ArticleRe: NSSA area-range command
Good that the info is of some help . [Click the "Star" for Kudos if you think I earned it!}
View ArticleRe: Which method easy to leak routes between two VRF?
Hi All, May i know whether vrf-target import target:x:x will overide vrf-target target:x:x ? As i'm understand the vrf-target target:x:x use to communicate with remote peer but what purpose of...
View ArticleRe: Which method easy to leak routes between two VRF?
vrf-target import target:x:x will override vrf-target target:x:x I assume this behavior has to do with the general convention of more specific ones being preferred ,over generic ones vrf-target...
View ArticlePrefix NLRI of BGP-ls
Hi, Experts, I made a simple test to export the TED to lsdist.0, only Nodes and Links NLRIs can be found in lsdist.0, no Prefix NLRI in there. I purposely exported an external route into ISIS, and...
View ArticleRe: Which method easy to leak routes between two VRF?
Hi Vinod, So u mean the vrf-target import target:4:4 and vrf-target export target:4:4 will replace / overide tag route the vrf-target target:x:x ? So if it overide then the Remote PE cannot connect...
View ArticleRe: Which method easy to leak routes between two VRF?
Yes vrf-target export and vrf-target import overrides vrf-target target:x:x Please use vrf-import and vrf-export instead of vrf-target import and vrf-target export, using this you can use multiple...
View ArticleRe: Which method easy to leak routes between two VRF?
Hi Vinod, If need use vrf-import and vrf-export it need a lot changes in entire PE customer because the existing network dont use community style. The just use vrf-target target:x:x to make sure other...
View ArticleRe: Which method easy to leak routes between two VRF?
Not sure about ways, other than community style for accepting/exporting multiple RT's , I will check for an alternative,if there is any. RIB groups can be done without config mistake . If you can share...
View Article