error message after typing "commit check" in MX
Hi After typing command "commit check" i got the below error message. and the bottom are its config. Anyone can explain it? Thank you AC0# commit checkre0: [edit routing-instances WSN] 'protocols'...
View ArticleRe: error message after typing "commit check" in MX
Hi eesunj, Please try "instance-type virtual-router" instead of "instance-type forwarding" to be able to support routing protocols.Then the commit should work.
View ArticleRe: MX route table size
Hello mueller, Can you share where you found this information? Regards.
View ArticleRe: MX route table size
Hi , this depends on configuration , and linecards you are using.MPC 1, MPC2 - 5M MPC2-NG, MPC3-NG, MPC5 - 10M Fib size for small MXs was in previous messages. Also , fib size depends on your...
View ArticleRe: Using EX3400 as a Router
Based on the specs of the 3400 and your requirements, it seems like this is the right switch. if you are not looking for advanced security features such as zonebased firewalling, UTM etc, then the...
View ArticleRe: Source Based - Routing
unit 125 { vlan-id 125; family inet { filter { input Content_Filter; } address 10.154.25.1/24; } } routing-options { interface-routes { rib-group inet Content_Filter; } static {route 0.0.0.0/0...
View ArticleeBGP policy and ACL in interface
Hi Anyone can answer the question? Two routers (RouterA and B) have eBGP connection. RouterA sends the routes 10.0.0.0 and 20.0.0.0 to routerB. The routerB’ interface allow 10.0.0.0 in and routerB’...
View ArticleRe: Source Based - Routing
import-rib [ inet.0 Content_Filter.inet.0]You need the correct routing instance name. Modify the import-rib statement like this[inet.0 Content_Filter_Instance. inet.0]
View ArticleDHCP Relay Not Working for Subscriber Management- MX80 BRAS/BNG !
I am trying to configure on MX80 BNG DHCP Relay for IPoE Subscribers ( transported via MPLS L2 VPN to the BNG). Psuedowire Subscriber Interface Solution is being used for MPLS Access ( "ps" interfaces...
View ArticleRe: eBGP policy and ACL in interface
I'm not sure that I understand the question. I think you are asking that if we have an ACL on an interface for blocking traffic, will that ACL have any affect on the ability of the eBGP peer to...
View ArticleRe: Does adding node-link protection cause LSP to flap?
Hi, To be precise, the flap can be avoided if the LSP is configured as 'adaptive' :set protocols mpls label-switched-path xxx adaptiveAlthough a new rsvp session is created, this happens in a...
View ArticleProblem with CBF
Hello!I’m having problem with CBF and multipath.Traffic with destination to 10.10.10.0/24 and dscp af need must use LSP r1-to-r3-af for forwardingTraffic with destination to 20.20.20.0/24 and dscp be...
View ArticleExport OSPF route in type-1
Hello,I have a QFX-1 which is learning route and 0.0.0.0/0 from OSPF I have connected a QFX-2 which is learning the route from QFX-1and 0.0.0.0/0 from OSPF too. The route are in OSPF TYPE-2How can we...
View ArticleRe: Export OSPF route in type-1
policy-options { policy-statement my-ospf-export-policy { term static-and-direct-as-type-1 { from protocol [ static direct ]; then { external { type 1; } accept; } } } } regards alexander
View ArticleRe: Export OSPF route in type-1
Hi,I always try this solution but it doesn't work:show policy-options policy-statement ospfbgpterm default-gw { from { route-filter 0.0.0.0/0 exact; } then { metric 200; external { type 1; } }} export...
View ArticleRe: Export OSPF route in type-1
Hello, maxx wrote:Hello,I have a QFX-1 which is learning route and 0.0.0.0/0 from OSPF I have connected a QFX-2 which is learning the route from QFX-1and 0.0.0.0/0 from OSPF too. The route are in OSPF...
View ArticleRe: Source Based - Routing
After the change suggested I was able to add the PC to the DC. But now I'm not able to navigate to any website. I created a rule that the segment where the PC is located pointed to the Security...
View Article