Re: Regarding command "show configuration | save Post"
Thank you for your reply. What is difference between below two sets of commands for rollback? First is:show configuration | save Filename load set Filename Second iscommitrollback 0
View ArticleRe: Cisco BGP Conversion
Hi, Config from I2J is complete: routing-options { autonomous-system 30;}protocols { bgp { path-selection cisco-non-deterministic; log-updown; group group-1 { type external; neighbor 172.16.3.2 {...
View ArticleClik here to view.
Re: Regarding command "show configuration | save Post"
'Load set' can be used not just for rollback but for other purposes as well . Most commonly if you need to deploy an high number of configuration lines.The rollback command on the other hand is only...
View ArticlePIM RP with bootstrap and Group Ranges
Hello, i was wondering if someone could help me understand this as i,m not sure if the output it being flaky for me. So i configured 2 routers in a network, Each with a seperate ip address for their...
View ArticleRe: PIM RP with bootstrap and Group Ranges
I think i answered my one question as i finally found the right documentation. So the lower the RP priority is set, the higher chance the router becomes the RP. And i finished labbing it up, So it...
View ArticleRe: Cisco BGP Conversion
Ashvin:Thank you for the output as when I did it there were many line in red indicating it could not interpret.Jeff
View ArticleRe: Regard command "commit comment PostN"
We add the change control number to the commit comments to help engineers find more detail when you they want to know about changes made on a device.
View ArticleRe: QoS scheduler on MX80
Hi pantunes, thanks for this book. it is very stright forward and helpfull. Chepter 2 Configuring BA Classifier - did the job - what I need it is simply classify packets based on dscp and put that to...
View ArticleRe: QoS scheduler on MX80
Now you need to apply the classifier to the interface unit at the ingress: set class-of-service interfaces xe-0/0/1 unit 0 classifiers dscp LTE_DSCP_Classfier You also need to apply the scheduler map...
View ArticleBackup-RE communication failure
hiInteresting problem, that has got me a running around the houses.So we have 2 setups, mx960 running 2x re-2000 and mx960 running 2x re-1800-s - as a note we are using a routing-instance, but this is...
View ArticleRe: Backup-RE communication failure
Hi CG, Not sure, if I understand your issue completely, but as you mentioned that backup RE is not able to reach any other subnets except the directly connected subnet, it would be good to check "show...
View ArticleRe: Backup-RE communication failure
Hi We have non-stop routing enabled, and able to see the route on the backup RE - these are routes that are contained within the routing-instance. Looking at the backup routing forwarding table, main...
View ArticleQueries regarding OSPF and LSP
Hi, I'm trying to make IGP learnt routes next hop to MPLS LSP by using the label-switched-path option in OSPF protocol. However the IGP learnt routes is no longer taking LSP as next hop when the LSP...
View ArticleRe: QoS scheduler on MX80
Thanks pantunes - by mistake I thought that classifiers should be under interface hierarchy - that is why I was confused. Thanks all the same :0 !
View ArticleCan't ping to IS-IS route.
Hello, I'm seeing route to reach 10.0.5/24 on R5 but i'm not able to ping or traceroute to 10.0.5.1 or 10.0.5.2 Ip address. Please see attached topology and router config. root@R5# run show route...
View ArticleRe: Can't ping to IS-IS route.
Hello, On R5, can you initiate ping to 10.0.5.2 source from interface connected to R6? Regards, Rushi
View ArticleRe: Can't ping to IS-IS route.
Hi Rushi, I can't ping on 10.0.5.2 fron R5 with source of 10.0.8.6( interface ip connected to R6)root@R5# run ping 10.0.5.2 source 10.0.8.6 PING 10.0.5.2 (10.0.5.2): 56 data bytes ^C --- 10.0.5.2 ping...
View ArticleRe: Can't ping to IS-IS route.
Hello, Then 10.0.5.2 may not have reverse route for 10.0.8.0/24 subnet but 10.0.5.1 appears to have it.What are 10.0.5.1 & 10.0.5.2 devices & can you check how 10.0.5.1 learns the route for...
View ArticleRe: Can't ping to IS-IS route.
Thanks Rushi ! Appriciate your time to look into this. There was bad config on R2 causing 10.0.5.2 to reject. I removed this config and its working now.root@R2# run show route 10.0.9.6 inet.0: 19...
View Article