Re: Network Design: Feedback on Regional Peering Concept
Hey Alex, Thank you for the detailed input, greatly appreciated. AS65124 has a single EBGP peering to AS100 in the master routing instance. As far as expected next hop, great question and I didn't...
View ArticleWake on LAN accross VLANs with targeted broadcast
Hi all, I'm trying to configure an EX3400 (JUNOS 15.1X53-D50.2) to route packets for Wake on LAN (sent from SCCM) accross VLANs. I've read the documentation which says that Targeted Broadcast is the...
View ArticleRe: Network Design: Feedback on Regional Peering Concept
Hello there,s702 wrote: The end goal is for half of my locations to prefer AS65150(west) default route, while the other half prefer AS65020(east) default route based upon a policy of my choosing.As I...
View ArticleRe: MX104 Circuit Breakers selection
Obviously using a larger fuse than required will work, but it removes a safety factor from the equation. This will allow too much current in the event of a problem. This can cause damage to the...
View ArticleRe: Can't announce redistributed routes from main instance
This is unfortunate that the lt are not supported in branch clusters. Obviously you can use physical interfaces or sub interfaces on the device to connect the two virutal routers via cabling and have...
View ArticleRe: Network Design: Feedback on Regional Peering Concept
Thanks for the diagram and further explanation. Another option in this setup would be to use FBF (filter based forwarding) routing at AS100 level. As noted, your downstream sites in this scenario are...
View ArticleRe: EVPN: No /32 route for existing MAC adress
Ballastic, Is the arp for .82 and .89 listed under "show arp no-resolve vpn HOSTING-VRF"? This looks to be an issue similar to the one mentioned in PR1180230 (MX) and this issue is fixed in 14.2R7.5...
View ArticleWhy can access router, but not Juniper via SecureCRT after changing from...
Hi, In GNS3 1.1, I can access router and Juniper via putty, but after I change from Putty(by default) to SecurityCRT in gns3, why I only can access router, but not Juniper? In the Juniper, i got this...
View ArticleRe: Wake on LAN accross VLANs with targeted broadcast
Hi Folks,I could come across with the below piece of information; can you please try using the knob forward-only rather than forward-and-send-to-re for isolation? Targeted broadcast does not work when...
View ArticleRe: Why can access router, but not Juniper via SecureCRT after changing from...
Change the version of ssh on juniper and see if that helps. It could be SeCRT is using version 2 only.
View ArticleRe: Traffic Shaping Problem on EX220
Would AppQoS be a useful feature to accomplish said objective?
View ArticleRe: Wake on LAN accross VLANs with targeted broadcast
Hi python, I already read and tried that - without success. The description also says this only happens with "an M320 router, a T640 router, or an MX960 router" whereas I have an EX3400. Futhermore, I...
View ArticleRe: Traffic Shaping Problem on EX220
Hello there, lyndidon wrote:Would AppQoS be a useful feature to accomplish said objective?AppQoS is not supported on EX2200.HTHThxAlex
View ArticleRe: Why can access router, but not Juniper via SecureCRT after changing from...
Hi Folks,It could be a path issue on calling the secureCRT exe file. Please refer this on some pointers on the same, https://www.youtube.com/watch?v=iua6MhYk0Ow
View ArticleRe: Why can access router, but not Juniper via SecureCRT after changing from...
@lyndidon, Thank you for your reply. I added some ssh commands as the below. but CRT still cannot access the Junos. I got the below output via putty. Can you take at the below? Thank you againroot@%...
View ArticleRe: Why can access router, but not Juniper via SecureCRT after changing from...
Hello there,eesunj wrote: why I only can access router, but not Juniper? In the Juniper, i got this error message in SecurityCRT: "The remote system refused the connection." Because Your JUNOS version...
View ArticleRe: Why can access router, but not Juniper via SecureCRT after changing from...
Hi Everyone, i am so sorry i did not make it clear. Please see attahced picture. I right click JunOS_R2, and then I click on Console to connect the juniper. then CRT is launched by the right click, but...
View ArticleRe: Why can access router, but not Juniper via SecureCRT after changing from...
Hi, It says "refused the connection" so mostly likely there are 2 possibilities: 1. The port used for console access is different when you open that session in secure CRT. Can you check what console...
View ArticleClik here to view.
Re: Traffic Shaping Problem on EX220
Duh!! SMH!! Not thinking clearly. Again...thankx. I need to think about the recommendations and teh supported platforms
View ArticleStatic Redistribution to OSPF
When using the standard static routing distrbution to ospf is there any reason it would not populate into OSPF? set interfaces ge-0/0/0 unit 0 family inet address 172.17.1.1/30 set routing-options...
View Article