Hi mriyaz,
when I run the command on router 1 it appears in state DR, bdr id 0.0.0.0 and nbrs 0. When I run the command on router 2 it appears in state DR, bdr id 0.0.0.0 and nbrs 1.
Thank you.
↧
Re: Problems with ospf in IPv6
↧
Re: How to establish a remote GW via L2circuit
Hi Alex
As the attachment is my configuration. Please refer to it.
Many thanks
Cloud
↧
↧
Re: How to establish a remote GW via L2circuit
Hello,
Thank You for sharing the configurations.
Please add this line into Your KR configuration
set logical-systems CHINA routing-instances HKG-KR-VPLS protocols vpls connectivity-type permanent
HTH
Thx
Alex
↧
Re: How to establish a remote GW via L2circuit
Hi Alex
Added, but is still same as before.
Best regards,
Cloud
↧
Re: Fortigate > Juniper 3300
Your problem is that the last two ports of your EX3300 is configured for virtual chassis. Seen when looking at the interfaces where you have two vcp-255 interfaces. If you replace vcp-255 with ge-0... there is your ge-0/1/3 interface :-)
root@STGPSW99> show interfaces Possible completions:<[Enter]> Execute this command<interface-name> Name of physical or logical interface vcp-255/1/2 vcp-255/1/2.32768 vcp-255/1/3 vcp-255/1/3.32768
To remove the virtual-chassis definition on the two ports, run these two commands in operational mode:
root@ex3300> request virtual-chassis vc-port delete pic-slot 1 port 2 root@ex3300> request virtual-chassis vc-port delete pic-slot 1 port 3
Then your ge-0/1/3 should show up correctly 
↧
↧
Re: Problems with ospf in IPv6
Hi CICA,
Did you see the corresponding interface on each router in the list?
For example if R1 (xe-0/0/0)--------------------(xe-0/0/0) R2
Then "show ospf3 interface" on each router can see xe-0/0/0.0. If yes, then please check "monitor traffic interface <intf-name> extensive no-resolve" on each router for this link and confirm if you see the other router's OSPF3 hello. Also ensure there's no generic IPv6 glitch for this link using "show interfaces terse <intf-name>" and "show ipv6 neighbors" on each router.
Hope this helps. Please let me know.
-r.
--------------------------------------------------
If this solves your problem, please mark this post as "Accepted Solution."
Kudos are always appreciated Smiley Happy.
↧
Re: How to establish a remote GW via L2circuit
Hello,
Please post the following printouts:
1/ from HK router
show route table inet.3 172.54.131.11
2/ from KR router
show route logical-system CHINA 173.198.146.6 table inet.3
HTH
Thx
Alex
↧
Re: LAG bundle on ACX 17.3R2.10 only uses one interface
In case anybody else here via google in the future...
Turns out there is no default hash-key algorithm setting for the LAG.
You must explicitly
set forwarding-options hash-key family inet layer-3 set forwarding-options hash-key family multiservice source-mac set forwarding-options hash-key family multiservice destination-mac
Then, and only then, layer 2 and layer 3 traffic will be load balanced across all physical links in the bundle...
↧
Re: How to establish a remote GW via L2circuit
Hi Alex
As follow is what you would like have. Should have been tagged by LDP.
HK> show route table inet.3 172.54.131.11
inet.3: 24 destinations, 24 routes (24 active, 0 holddown, 0 hidden)
+ = Active Route, - = Last Active, * = Both
172.54.131.11/32 *[LDP/9] 6d 15:28:54, metric 27
> to 10.3.100.38 via ae8.1, Push 307344
to 10.5.100.57 via xe-1/3/2.0, Push 310080
KR> show route logical-system CHINA 173.198.146.6 table inet.3
inet.3: 24 destinations, 24 routes (24 active, 0 holddown, 0 hidden)
+ = Active Route, - = Last Active, * = Both
173.198.146.6/32 *[LDP/9] 6d 15:29:26, metric 27
> to 10.24.100.97 via lt-1/2/0.1, Push 308032
to 10.24.100.101 via lt-4/2/0.1, Push 308032
Best regards,
Cloud
↧
↧
Re: How to establish a remote GW via L2circuit
Hi Alex
I found out my loopback's filter denying l2circuit connections. Now is up,but display Vlan ID mismatch.
Instance: HKG02-KMH05-VPLS
VPLS-id: 10011
Neighbor Type St Time last up # Up trans
173.198.146.6(vpls-id 10011) rmt VM
local PW status code: 0x00000001, Neighbor PW status code: 0x00000000
Best regards,
Cloud
↧
Re: How to establish a remote GW via L2circuit
Hello,
Two ways to deal with L2circuit "vlan-mismatch":
1/ add "ignore-vlan-mismatch" under neighbor on each side
2/ change encapsulation under neighbor on each side to "ethernet-ccc"
HTH
Thx
Alex
↧
Re: How to establish a remote GW via L2circuit
Hi Alex
I've tested these two way, but only have "ignore-encapsulation-mismatch" and "ethernet-vlan" under neighbor.
Thus, these two way are not working.
Best regards,
Cloud
↧
Re: How to establish a remote GW via L2circuit
Hi Alex
I've changed it as "ethernet-vlan" on both side and is working.
I add irb into VRF and my server will connect to Internet via KR.
Thanks for your support.
Best regards,
Cloud
↧
↧
Re: Problems with ospf in IPv6
Hi CICA,
Please update if you resolved it, so the post could be beneficial for others too.
-r.
--------------------------------------------------
If this solves your problem, please mark this post as "Accepted Solution."
Kudos are always appreciated Smiley Happy.
↧
IS-IS run over GRE
Hi All
I ever ran OSPF over GRE and was fine, but IS-IS not. Looks like that it connected via GRE failed for IS-IS.
Is there anyone have the same experience to set up like this ?
As follow is my configuration :
> show configuration interfaces gr-5/0/0
unit 1 {
tunnel {
source 62.115.162.53;
destination 218.30.53.190;
}
family inet {
mtu 1476;
tcp-mss 1436;
address 172.54.129.50/30;
}
family iso;
family mpls;
}
> show configuration protocols isis
interface gr-5/0/0.1 {
point-to-point;
level 2 metric 200;
level 1 disable;
}
> show isis adjacency detail
1000.3100.0002
Interface: gr-5/0/0.1, Level: 2, State: Initializing, Expires in 22 secs
Priority: 0, Up/Down transitions: 0, Last transition: 00:29:24 ago
Circuit type: 2, Speaks: IP, IPv6
Topologies: Unicast
Restart capable: Yes, Adjacency advertisement: Advertise
IP addresses: 172.54.129.49
Best regards,
Cloud
↧
Re: IS-IS run over GRE
Possible MTU issue.
Can you increase it more than 1492 and check? as far as i remeber, isis will not comeup if mtu is less than 1492 bytes
↧
Re: SRX 550 - OSPF Adjacency Stuck in ExStart State
show log ospf-log Aug 2 08:59:55 trace_on: Tracing to "/var/log/ospf-log" started Aug 2 08:59:55.841376 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Keepalive <Touched> set to offset 40 at 9:00:35 Aug 2 08:59:55.841603 background dispatch running job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.841646 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Keepalive <Touched> set to offset 40 at 9:00:35 Aug 2 08:59:55.841707 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Keepalive <Touched> set to offset 40 at 9:00:35 Aug 2 08:59:55.841765 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Keepalive <Touched> set to offset 40 at 9:00:35 Aug 2 08:59:55.841821 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Keepalive <Touched> set to offset 40 at 9:00:35 Aug 2 08:59:55.841861 OSPF restart signaling: set L bit in hellos sent on interface lo0.0. Aug 2 08:59:55.841889 OSPF restart signaling: set L bit in hellos sent on interface reth0.0. Aug 2 08:59:55.841917 OSPF sent Hello 192.168.1.6 -> 224.0.0.5 (reth0.0 IFL 67 area 0.0.0.20) Aug 2 08:59:55.841940 Version 2, length 48, ID 192.168.1.6, area 0.0.0.20 Aug 2 08:59:55.841963 mask 255.255.255.248, hello_ivl 10, opts 0x12, prio 128 Aug 2 08:59:55.841983 dead_ivl 40, DR 192.168.1.6, BDR 192.168.1.1 Aug 2 08:59:55.842002 neighbor 192.168.1.1 Aug 2 08:59:55.842028 OSPF restart signaling: Add LLS data for Hello packet on interface reth0.0. Aug 2 08:59:55.842069 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Keepalive <Touched> set to offset 40 at 9:00:35 Aug 2 08:59:55.842113 task_job_delete: delete background job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.842144 background dispatch completed job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.842373 IFL ge-9/0/9.0 iflchange 0x0 Aug 2 08:59:55.842465 IFL ge-9/0/8.0 iflchange 0x0 Aug 2 08:59:55.842555 IFL ge-9/0/7.0 iflchange 0x0 Aug 2 08:59:55.842643 IFL ge-9/0/6.0 iflchange 0x0 Aug 2 08:59:55.842765 IFL ge-9/0/5.0 iflchange 0x0 Aug 2 08:59:55.842854 IFL ge-9/0/4.0 iflchange 0x0 Aug 2 08:59:55.842943 IFL ge-9/0/3.0 iflchange 0x0 Aug 2 08:59:55.843036 IFL ge-9/0/2.0 iflchange 0x0 Aug 2 08:59:55.843130 IFL fab1.0 iflchange 0x0 Aug 2 08:59:55.843222 IFL ge-0/0/9.0 iflchange 0x0 Aug 2 08:59:55.843310 IFL ge-0/0/8.0 iflchange 0x0 Aug 2 08:59:55.843397 IFL ge-0/0/7.0 iflchange 0x0 Aug 2 08:59:55.843485 IFL ge-0/0/6.0 iflchange 0x0 Aug 2 08:59:55.843575 IFL ge-0/0/5.0 iflchange 0x0 Aug 2 08:59:55.843663 IFL ge-0/0/4.0 iflchange 0x0 Aug 2 08:59:55.843752 IFL ge-0/0/3.0 iflchange 0x0 Aug 2 08:59:55.843840 IFL ge-0/0/2.0 iflchange 0x0 Aug 2 08:59:55.843933 IFL fab0.0 iflchange 0x0 Aug 2 08:59:55.844037 IFL reth2.0 iflchange 0x0 Aug 2 08:59:55.844135 IFL reth1.0 iflchange 0x0 Aug 2 08:59:55.844231 IFL reth0.0 iflchange 0x0 Aug 2 08:59:55.844314 IFL lo0.16385 iflchange 0x0 Aug 2 08:59:55.844369 IFL lo0.16384 iflchange 0x0 Aug 2 08:59:55.844440 IFL lo0.0 iflchange 0x0 Aug 2 08:59:55.844534 IFL fxp2.0 iflchange 0x0 Aug 2 08:59:55.844616 IFL fxp1.0 iflchange 0x0 Aug 2 08:59:55.844689 IFL fxp0.0 iflchange 0x0 Aug 2 08:59:55.844982 IFL fxp0.0 addr (10.251.200.5) ifachange 0x0 Aug 2 08:59:55.845447 IFL lo0.0 addr (2.2.2.2) ifachange 0x0 Aug 2 08:59:55.845816 IFL reth0.0 addr (192.168.1.6) ifachange 0x0 Aug 2 08:59:55.847671 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.847732 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.847781 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Hold <Touched> set to offset 2:00 at 9:01:55 Aug 2 08:59:55.847809 ppmd_ospf_intf_auth_key_select : interface lo0.0 Aug 2 08:59:55.847855 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.847911 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.847960 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Hold <Touched> set to offset 2:00 at 9:01:55 Aug 2 08:59:55.847988 No OSPF authentication key active (now : 0) Aug 2 08:59:55.848057 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.848117 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.848165 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Hold <Touched> set to offset 2:00 at 9:01:55 Aug 2 08:59:55.848192 OSPF updated PPM interface IFL 66, addr 2.2.2.2, area 0.0.0.20, ID 0.0.0.0, rtbl idx 0 Aug 2 08:59:55.848249 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.848305 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.848352 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Hold <Touched> set to offset 2:00 at 9:01:55 Aug 2 08:59:55.848379 ppmd_ospf_intf_auth_key_select : interface reth0.0 Aug 2 08:59:55.848424 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.848479 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.848527 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Hold <Touched> set to offset 2:00 at 9:01:55 Aug 2 08:59:55.848557 No OSPF authentication key active (now : 0) Aug 2 08:59:55.848612 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.848669 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.848717 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Hold <Touched> set to offset 2:00 at 9:01:55 Aug 2 08:59:55.848745 OSPF updated PPM interface IFL 67, addr 192.168.1.6, area 0.0.0.20, ID 0.0.0.0, rtbl idx 0 Aug 2 08:59:55.848798 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.848854 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.848903 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Hold <Touched> set to offset 2:00 at 9:01:55 Aug 2 08:59:55.848931 OSPF neighbor 192.168.1.1 (IFL 67, area 0.0.0.20, rtbl idx 0) set, 40 0 Aug 2 08:59:55.848993 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.849055 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.849103 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Hold <Touched> set to offset 2:00 at 9:01:55 Aug 2 08:59:55.849131 OSPF programmed periodic xmit from 192.168.1.6 to 224.0.0.5 (IFL 67, area 0.0.0.20, ID 0.0.0.0, rtbl idx 0) interval 10 0 Aug 2 08:59:55.849217 background dispatch running job Interface event for task OSPF Aug 2 08:59:55.849248 Interface lo0.0 area 0.0.0.20 event NeighborChange Aug 2 08:59:55.849281 task_job_create_background: create prio 1 job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.849310 Interface lo0.0 (2.2.2.2) area 0.0.0.20 state changed from DR to DR Aug 2 08:59:55.849337 OSPF DR is 192.168.1.6, BDR is 0.0.0.0 Aug 2 08:59:55.849364 Interface reth0.0 area 0.0.0.20 event NeighborChange Aug 2 08:59:55.849392 Interface reth0.0 (192.168.1.6) area 0.0.0.20 state changed from DR to DR Aug 2 08:59:55.849419 OSPF DR is 192.168.1.6, BDR is 192.168.1.1 Aug 2 08:59:55.849441 OSPF Interface event job processed 2 events. Aug 2 08:59:55.849460 OSPF Interface event job deleted. Aug 2 08:59:55.849482 task_job_delete: delete background job Interface event for task OSPF Aug 2 08:59:55.849506 background dispatch completed job Interface event for task OSPF Aug 2 08:59:55.849596 background dispatch running job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.849625 OSPF restart signaling: set L bit in hellos sent on interface lo0.0. Aug 2 08:59:55.849648 OSPF restart signaling: set L bit in hellos sent on interface reth0.0. Aug 2 08:59:55.849674 OSPF sent Hello 192.168.1.6 -> 224.0.0.5 (reth0.0 IFL 67 area 0.0.0.20) Aug 2 08:59:55.849697 Version 2, length 48, ID 192.168.1.6, area 0.0.0.20 Aug 2 08:59:55.849719 mask 255.255.255.248, hello_ivl 10, opts 0x12, prio 128 Aug 2 08:59:55.849740 dead_ivl 40, DR 192.168.1.6, BDR 192.168.1.1 Aug 2 08:59:55.849779 neighbor 192.168.1.1 Aug 2 08:59:55.849802 OSPF restart signaling: Add LLS data for Hello packet on interface reth0.0. Aug 2 08:59:55.849841 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Keepalive <Touched> set to offset 40 at 9:00:35 Aug 2 08:59:55.849889 task_job_delete: delete background job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.849919 background dispatch completed job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.850019 rt_flash_update_callback: flash OSPF (inet.0) start Aug 2 08:59:55.850711 Starting flash processing for topology default Aug 2 08:59:55.850751 Context-Id is inactive in MPLS and will be deleted from OSPF Aug 2 08:59:55.850783 Context-Id is inactive in MPLS and will be deleted from OSPF Aug 2 08:59:55.850828 Context-Id is inactive in MPLS and will be deleted from OSPF Aug 2 08:59:55.850874 Context-Id is inactive in MPLS and will be deleted from OSPF Aug 2 08:59:55.850903 Context-Id is inactive in MPLS and will be deleted from OSPF Aug 2 08:59:55.850931 Context-Id is inactive in MPLS and will be deleted from OSPF Aug 2 08:59:55.850958 OSPF: multicast address 224.0.0.5/32, route ignored Aug 2 08:59:55.850985 Redist elapsed time 0.000243s Aug 2 08:59:55.851006 Processed 7 routes Aug 2 08:59:55.851024 Finished flash processing for topology default Aug 2 08:59:55.851055 rt_flash_update_callback: flash OSPF (inet.0) done Aug 2 08:59:55.851319 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.851378 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:55.851428 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Hold <Touched> set to offset 2:00 at 9:01:55 Aug 2 08:59:55.851456 OSPF programmed periodic xmit from 192.168.1.6 to 224.0.0.5 (IFL 67, area 0.0.0.20, ID 0.0.0.0, rtbl idx 0) interval 10 0 Aug 2 08:59:55.883237 ospf_set_lsdb_state: Router LSA 192.168.1.6 adv-rtr 192.168.1.6 state GEN_PENDING->QUIET Aug 2 08:59:55.883316 OSPF built router LSA, area 0.0.0.20, link count 3 Aug 2 08:59:55.883381 task_timer_reset: reset OSPF_LSA gen Aug 2 08:59:55.883425 task_timer_uset: timer OSPF_LSA gen <Touched Processing> set to offset 46:13 at 9:46:08 Aug 2 08:59:55.883452 LSA Router 192.168.1.6 192.168.1.6 not refreshed as there in no changein LSA body. LSA refresh time 00:46:13 Aug 2 08:59:56.034604 task_job_create_background: create prio 2 job Route recalc timer for task OSPF Aug 2 08:59:56.034697 background dispatch running job Route recalc timer for task OSPF Aug 2 08:59:56.034728 Starting full SPF refresh for topology default Aug 2 08:59:56.034785 SPF starting for area 0.0.0.20 Aug 2 08:59:56.034820 OSPF add LSA Router (192.168.1.6, 192.168.1.6) distance 0 to SPF list Aug 2 08:59:56.034846 SPF finished for area 0.0.0.20 Aug 2 08:59:56.034879 SPF elapsed time 0.000094s Aug 2 08:59:56.034906 SPF add stubs starting for area 0.0.0.20 Aug 2 08:59:56.034941 IP Nexthop #1 (null):192.168.1.6 (lo0.0) added Aug 2 08:59:56.034975 Adding stub route 2.2.2.2/32 Aug 2 08:59:56.035007 IP Route added with cost 0 Aug 2 08:59:56.035040 IP Nexthop #1 (null):192.168.1.6 (lo0.0) added Aug 2 08:59:56.035069 Adding stub route 2.2.2.0/24 Aug 2 08:59:56.035096 IP Route added with cost 0 Aug 2 08:59:56.035127 IP Nexthop #1 (null):192.168.1.6 (reth0.0) added Aug 2 08:59:56.035156 Adding stub route 38.87.38.0/29 Aug 2 08:59:56.035183 IP Route added with cost 1 Aug 2 08:59:56.035205 SPF add stubs finished for area 0.0.0.20 Aug 2 08:59:56.035229 Stub elapsed time 0.000324s Aug 2 08:59:56.035255 SPF add inter area starting for area 0.0.0.20 Aug 2 08:59:56.035277 SPF add inter area Summary starting for area 0.0.0.20 Aug 2 08:59:56.035298 SPF add inter area Summary finished for area 0.0.0.20 Aug 2 08:59:56.035319 SPF add inter area ASBRSum starting for area 0.0.0.20 Aug 2 08:59:56.035340 SPF add inter area ASBRSum finished for area 0.0.0.20 Aug 2 08:59:56.035360 SPF add inter area finished for area 0.0.0.20 Aug 2 08:59:56.035415 Interarea elapsed time 0.000157s Aug 2 08:59:56.035439 SPF add external starting Aug 2 08:59:56.035466 SPF add external finished Aug 2 08:59:56.035491 External elapsed time 0.000050s Aug 2 08:59:56.035512 SPF add NSSA starting Aug 2 08:59:56.035537 SPF add NSSA finished Aug 2 08:59:56.035561 NSSA elapsed time 0.000048s Aug 2 08:59:56.035583 SPF post spf cleanup starting Aug 2 08:59:56.035634 Route 2.2.2.0/24 has been refreshed Aug 2 08:59:56.035664 Considering autosummary for 2.2.2.0/24, summary possible=1 Aug 2 08:59:56.035689 Considering NSSA autosummary for 2.2.2.0/24, summary not possible Aug 2 08:59:56.035731 Route 2.2.2.2/32 has been refreshed Aug 2 08:59:56.035760 Considering autosummary for 2.2.2.2/32, summary possible=1 Aug 2 08:59:56.035784 Considering NSSA autosummary for 2.2.2.2/32, summary not possible Aug 2 08:59:56.035820 Manual summary 38.87.38.0/29, area 0.0.0.20, route 38.87.38.0/29, metric 16777215->1 Aug 2 08:59:56.035856 Route 38.87.38.0/29 has been refreshed Aug 2 08:59:56.035883 Considering autosummary for 38.87.38.0/29, summary possible=1 Aug 2 08:59:56.035907 Considering NSSA autosummary for 38.87.38.0/29, summary not possible Aug 2 08:59:56.035940 SPF post spf cleanup finished Aug 2 08:59:56.035970 Cleanup elapsed time 0.000385s Aug 2 08:59:56.035993 Total elapsed time 0.001268s Aug 2 08:59:56.036015 Finished full SPF refresh for topology default Aug 2 08:59:56.036040 task_job_delete: delete background job Route recalc timer for task OSPF Aug 2 08:59:56.036077 background dispatch completed job Route recalc timer for task OSPF Aug 2 08:59:56.521668 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:56.521750 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:56.521808 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Hold <Touched> set to offset 2:00 at 9:01:56 Aug 2 08:59:56.521848 Received OSPF packet of type and wire_length 1, 48 Aug 2 08:59:56.521878 OSPF rcvd Hello 192.168.1.1 -> 224.0.0.5 (reth0.0 IFL 67 area 0.0.0.20) Aug 2 08:59:56.521928 Version 2, length 48, ID 192.168.1.1, area 0.0.0.20 Aug 2 08:59:56.521951 checksum 0x0, authtype 0 Aug 2 08:59:56.521973 mask 255.255.255.248, hello_ivl 10, opts 0x2, prio 1 Aug 2 08:59:56.521994 dead_ivl 40, DR 192.168.1.6, BDR 192.168.1.1 Aug 2 08:59:56.522014 neighbor 192.168.1.6 Aug 2 08:59:56.522046 OSPF restart signaling: Received hello with LR bit set from nbr ip=192.168.1.1 id=192.168.1.1. Set oob-resync capabilty 0. Aug 2 08:59:56.522085 OSPF restart signaling:Save_packet length 48 : Aug 2 08:59:56.522126 task_job_create_background: create prio 1 job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 08:59:56.522178 background dispatch running job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 08:59:56.522226 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Keepalive <Touched> set to offset 40 at 9:00:36 Aug 2 08:59:56.522275 task_job_delete: delete background job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 08:59:56.522323 background dispatch completed job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 08:59:56.522571 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:56.522635 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 08:59:56.522685 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Hold <Touched> set to offset 2:00 at 9:01:56 Aug 2 08:59:56.522714 OSPF neighbor 192.168.1.1 (IFL 67, area 0.0.0.20, rtbl idx 0) set, 40 0 Aug 2 08:59:57.335683 OSPF resend last DBD to 192.168.1.1 Aug 2 08:59:57.335790 task_timer_uset: timer OSPF_Global xmit timer <Touched> set to interval 0.040000 jitter 10 at 8:59:57 Aug 2 08:59:57.335821 task_timer_expire_immediately: timer OSPF_Global xmit timer set to expire now Aug 2 08:59:57.335844 OSPF retransmitting DBD to 192.168.1.1 Aug 2 08:59:57.335884 OSPF sent DbD 192.168.1.6 -> 192.168.1.1 (reth0.0 IFL 67 area 0.0.0.20) Aug 2 08:59:57.335952 Version 2, length 32, ID 192.168.1.6, area 0.0.0.20 Aug 2 08:59:57.335978 options 0x52, i 1, m 1, ms 1, r 0, seq 0x26502402, mtu 1508 Aug 2 08:59:57.336000 OSPF restart signaling: Add LLS data for DbD packet on interface reth0.0. Aug 2 08:59:57.336043 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Keepalive <Touched> set to offset 40 at 9:00:37 Aug 2 08:59:57.336094 task_timer_reset: reset OSPF_DBD rexmit Aug 2 08:59:57.336127 task_timer_set_oneshot_latest: timer OSPF_DBD rexmit interval set to 4.881794 Aug 2 08:59:57.372658 task_timer_reset: reset OSPF_Global xmit timer Aug 2 09:00:02.219216 OSPF resend last DBD to 192.168.1.1 Aug 2 09:00:02.219323 task_timer_uset: timer OSPF_Global xmit timer <Touched> set to interval 0.040000 jitter 10 at 9:00:02 Aug 2 09:00:02.219354 task_timer_expire_immediately: timer OSPF_Global xmit timer set to expire now Aug 2 09:00:02.219375 OSPF retransmitting DBD to 192.168.1.1 Aug 2 09:00:02.219415 OSPF sent DbD 192.168.1.6 -> 192.168.1.1 (reth0.0 IFL 67 area 0.0.0.20) Aug 2 09:00:02.219440 Version 2, length 32, ID 192.168.1.6, area 0.0.0.20 Aug 2 09:00:02.219463 options 0x52, i 1, m 1, ms 1, r 0, seq 0x26502402, mtu 1508 Aug 2 09:00:02.219485 OSPF restart signaling: Add LLS data for DbD packet on interface reth0.0. Aug 2 09:00:02.219529 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Keepalive <Touched> set to offset 40 at 9:00:42 Aug 2 09:00:02.219581 task_timer_reset: reset OSPF_DBD rexmit Aug 2 09:00:02.219611 task_timer_set_oneshot_latest: timer OSPF_DBD rexmit interval set to 4.731876 Aug 2 09:00:02.258206 task_timer_reset: reset OSPF_Global xmit timer Aug 2 09:00:03.149445 OSPF neighbor 192.168.1.1 (realm ospf-v2 reth0.0 area 0.0.0.20) state changed from ExStart to Down due to KillNbr (event reason: command to clear a neighbor was issued) (nbr helped: 0) Aug 2 09:00:03.149604 RPD_OSPF_NBRDOWN: OSPF neighbor 192.168.1.1 (realm ospf-v2 reth0.0 area 0.0.0.20) state changed from ExStart to Down due to KillNbr (event reason: command to clear a neighbor was issued) Aug 2 09:00:03.149683 task_job_create_background: create prio 4 job Interface event for task OSPF Aug 2 09:00:03.149708 OSPF Interface event job created at restart phase 0. Aug 2 09:00:03.149746 task_job_create_background: create prio 1 job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 09:00:03.149785 task_timer_delete: OSPF_DBD rexmit <Touched> Aug 2 09:00:03.149815 OSPF 192.168.1.1 DBD cleanup complete Aug 2 09:00:03.149845 task_timer_delete: OSPF_Grace timer <> Aug 2 09:00:03.149876 task_timer_delete: OSPF_Neighbor rexmit <> Aug 2 09:00:03.149901 task_timer_delete: OSPF_resync timeout <> Aug 2 09:00:03.149925 task_timer_delete: OSPF_resync timeout <> Aug 2 09:00:03.150022 background dispatch running job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 09:00:03.150072 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Keepalive <Touched> set to offset 40 at 9:00:43 Aug 2 09:00:03.150136 task_job_delete: delete background job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 09:00:03.150168 background dispatch completed job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 09:00:03.150212 background dispatch running job Interface event for task OSPF Aug 2 09:00:03.150241 Interface reth0.0 area 0.0.0.20 event NeighborChange Aug 2 09:00:03.150656 task_job_create_background: create prio 1 job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 09:00:03.150689 Interface reth0.0 (192.168.1.6) area 0.0.0.20 state changed from DR to DR Aug 2 09:00:03.150717 OSPF DR is 192.168.1.6, BDR is 0.0.0.0 Aug 2 09:00:03.150747 ospf_set_lsdb_state: Router LSA 192.168.1.6 adv-rtr 192.168.1.6 state QUIET->GEN_PENDING Aug 2 09:00:03.150775 task_timer_reset: reset OSPF_LSA gen Aug 2 09:00:03.150807 task_timer_uset: timer OSPF_LSA gen <Touched> set to offset 0.050000 at 9:00:03 Aug 2 09:00:03.150831 OSPF trigger router LSA 0x13b80e8 build for area 0.0.0.20 lsa-id 192.168.1.6 Aug 2 09:00:03.150874 ospf_trigger_build_telink_lsas : No peer found Aug 2 09:00:03.150901 OSPF Interface event job processed 1 events. Aug 2 09:00:03.150921 OSPF Interface event job deleted. Aug 2 09:00:03.150942 task_job_delete: delete background job Interface event for task OSPF Aug 2 09:00:03.150967 background dispatch completed job Interface event for task OSPF Aug 2 09:00:03.151010 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 09:00:03.151069 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 09:00:03.151119 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Hold <Touched> set to offset 2:00 at 9:02:03 Aug 2 09:00:03.151148 OSPF neighbor 192.168.1.1 (IFL 67, area 0.0.0.20, rtbl idx 0) deleted Aug 2 09:00:03.151201 background dispatch running job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 09:00:03.151231 OSPF restart signaling: set L bit in hellos sent on interface reth0.0. Aug 2 09:00:03.152386 OSPF sent Hello 192.168.1.6 -> 224.0.0.5 (reth0.0 IFL 67 area 0.0.0.20) Aug 2 09:00:03.152416 Version 2, length 44, ID 192.168.1.6, area 0.0.0.20 Aug 2 09:00:03.152440 mask 255.255.255.248, hello_ivl 10, opts 0x12, prio 128 Aug 2 09:00:03.152460 dead_ivl 40, DR 192.168.1.6, BDR 0.0.0.0 Aug 2 09:00:03.152482 OSPF restart signaling: Add LLS data for Hello packet on interface reth0.0. Aug 2 09:00:03.152524 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Keepalive <Touched> set to offset 40 at 9:00:43 Aug 2 09:00:03.152573 task_job_delete: delete background job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 09:00:03.152604 background dispatch completed job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 09:00:03.154668 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 09:00:03.154729 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 09:00:03.154781 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Hold <Touched> set to offset 2:00 at 9:02:03 Aug 2 09:00:03.154826 OSPF programmed periodic xmit from 192.168.1.6 to 224.0.0.5 (IFL 67, area 0.0.0.20, ID 0.0.0.0, rtbl idx 0) interval 10 0 Aug 2 09:00:03.201308 ospf_set_lsdb_state: Router LSA 192.168.1.6 adv-rtr 192.168.1.6 state GEN_PENDING->QUIET Aug 2 09:00:03.201354 OSPF built router LSA, area 0.0.0.20, link count 3 Aug 2 09:00:03.201384 Clear inverse links started for area 0.0.0.20 Router lsa id 192.168.1.6 adv rtr 192.168.1.6 Aug 2 09:00:03.201409 Clear inverse links finished for area 0.0.0.20 Router lsa id 192.168.1.6 adv rtr 192.168.1.6 Aug 2 09:00:03.201434 task_timer_reset: reset OSPF_LSA gen Aug 2 09:00:03.201465 task_timer_uset: timer OSPF_LSA gen <Touched Processing> set to offset 50:00 at 9:50:03 Aug 2 09:00:03.201496 LSA Router 192.168.1.6 192.168.1.6 flood state Idle -> Idle, new LSA Aug 2 09:00:03.201524 task_timer_reset: reset OSPF_LSA age Aug 2 09:00:03.201550 task_timer_set_oneshot_latest: timer OSPF_LSA age interval set to 1:00:00 Aug 2 09:00:03.201580 LSA analysis started for area 0.0.0.20 Router lsa id 192.168.1.6 adv rtr 192.168.1.6 Aug 2 09:00:03.201604 LSA analysis finished for area 0.0.0.20 Router lsa id 192.168.1.6 adv rtr 192.168.1.6 Aug 2 09:00:03.201627 Setup inverse links started for area 0.0.0.20 Router lsa id 192.168.1.6 adv rtr 192.168.1.6 Aug 2 09:00:03.201650 Setup inverse links finished for area 0.0.0.20 Router lsa id 192.168.1.6 adv rtr 192.168.1.6 Aug 2 09:00:03.201675 LSA Router 192.168.1.6 192.168.1.6 flood state Idle -> Standby send, flooding Aug 2 09:00:03.201697 Updating LSA Router 192.168.1.6 192.168.1.6 (flood state Standby send) Aug 2 09:00:03.201720 LSA Router 192.168.1.6 192.168.1.6 flood state Standby send -> Wait nbr ack, not queued Aug 2 09:00:03.201742 OSPF flooding restarted, depth 1, rexmit 0 Aug 2 09:00:03.201767 task_job_create_background: create prio 3 job OSPF flood for task OSPF Aug 2 09:00:03.201815 background dispatch running job OSPF flood for task OSPF Aug 2 09:00:03.201842 task_timer_reset: reset OSPF_Flood timer Aug 2 09:00:03.201889 OSPF LSA Router 192.168.1.6 192.168.1.6 on no lo0.0 area 0.0.0.20 rexmit lists, no flood Aug 2 09:00:03.201916 OSPF LSA Router 192.168.1.6 192.168.1.6 on no reth0.0 area 0.0.0.20 rexmit lists, no flood Aug 2 09:00:03.201940 LSA Router 192.168.1.6 192.168.1.6 flood state Wait nbr ack -> Idle, not queued Aug 2 09:00:03.201964 task_job_delete: delete background job OSPF flood for task OSPF Aug 2 09:00:03.201999 background dispatch completed job OSPF flood for task OSPF Aug 2 09:00:04.822477 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 09:00:04.822596 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 09:00:04.822651 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Hold <Touched> set to offset 2:00 at 9:02:04 Aug 2 09:00:04.822691 Received OSPF packet of type and wire_length 1, 48 Aug 2 09:00:04.822720 OSPF rcvd Hello 192.168.1.1 -> 224.0.0.5 (reth0.0 IFL 67 area 0.0.0.20) Aug 2 09:00:04.822743 Version 2, length 48, ID 192.168.1.1, area 0.0.0.20 Aug 2 09:00:04.822763 checksum 0x0, authtype 0 Aug 2 09:00:04.822784 mask 255.255.255.248, hello_ivl 10, opts 0x2, prio 1 Aug 2 09:00:04.822805 dead_ivl 40, DR 192.168.1.1, BDR 0.0.0.0 Aug 2 09:00:04.822824 neighbor 192.168.1.6 Aug 2 09:00:04.822872 task_timer_ucreate: created timer OSPF_Neighbor rexmit flags <> Aug 2 09:00:04.822904 task_timer_ucreate: created timer OSPF_resync timeout flags <> Aug 2 09:00:04.822929 task_timer_ucreate: created timer OSPF_resync timeout flags <> Aug 2 09:00:04.822957 task_timer_ucreate: created timer OSPF_Grace timer flags <> Aug 2 09:00:04.822994 task_job_create_background: create prio 1 job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 09:00:04.823025 OSPF neighbor 192.168.1.1 (realm ospf-v2 reth0.0 area 0.0.0.20) state changed from Down to Init due to HelloRcvd (event reason: Hello message received) (nbr helped: 0) Aug 2 09:00:04.823057 OSPF restart signaling: Received hello with LR bit set from nbr ip=192.168.1.1 id=192.168.1.1. Set oob-resync capabilty 0. Aug 2 09:00:04.823116 OSPF neighbor 192.168.1.1 (realm ospf-v2 reth0.0 area 0.0.0.20) state changed from Init to ExStart due to 2WayRcvd (event reason: neighbor detected this router) (nbr helped: 0) Aug 2 09:00:04.823247 RPD_OSPF_NBRUP: OSPF neighbor 192.168.1.1 (realm ospf-v2 reth0.0 area 0.0.0.20) state changed from Init to ExStart due to 2WayRcvd (event reason: neighbor detected this router) Aug 2 09:00:04.823283 task_job_create_background: create prio 4 job Interface event for task OSPF Aug 2 09:00:04.823306 OSPF Interface event job created at restart phase 0. Aug 2 09:00:04.823336 1400 Max dbd packet Aug 2 09:00:04.823365 OSPF restart signaling: Send DBD with LR bit on to nbr ip=192.168.1.1 id=192.168.1.1. Aug 2 09:00:04.823413 task_timer_uset: timer OSPF_Global xmit timer <Touched> set to interval 0.040000 jitter 10 at 9:00:04 Aug 2 09:00:04.823443 task_timer_expire_immediately: timer OSPF_Global xmit timer set to expire now Aug 2 09:00:04.823472 OSPF restart signaling:Save_packet length 48 : Aug 2 09:00:04.823517 task_timer_ucreate: created timer OSPF_DBD rexmit flags <> Aug 2 09:00:04.823553 task_timer_reset: reset OSPF_DBD rexmit Aug 2 09:00:04.823583 task_timer_set_oneshot_latest: timer OSPF_DBD rexmit interval set to 4.854189 Aug 2 09:00:04.823648 background dispatch running job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 09:00:04.823698 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Keepalive <Touched> set to offset 40 at 9:00:44 Aug 2 09:00:04.823746 OSPF restart signaling: set L bit in hellos sent on interface reth0.0. Aug 2 09:00:04.823778 OSPF sent Hello 192.168.1.6 -> 224.0.0.5 (reth0.0 IFL 67 area 0.0.0.20) Aug 2 09:00:04.823801 Version 2, length 48, ID 192.168.1.6, area 0.0.0.20 Aug 2 09:00:04.823823 mask 255.255.255.248, hello_ivl 10, opts 0x12, prio 128 Aug 2 09:00:04.823844 dead_ivl 40, DR 192.168.1.6, BDR 0.0.0.0 Aug 2 09:00:04.823863 neighbor 192.168.1.1 Aug 2 09:00:04.823886 OSPF restart signaling: Add LLS data for Hello packet on interface reth0.0. Aug 2 09:00:04.823953 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Keepalive <Touched> set to offset 40 at 9:00:44 Aug 2 09:00:04.823999 OSPF sent DbD 192.168.1.6 -> 192.168.1.1 (reth0.0 IFL 67 area 0.0.0.20) Aug 2 09:00:04.824024 Version 2, length 32, ID 192.168.1.6, area 0.0.0.20 Aug 2 09:00:04.824047 options 0x52, i 1, m 1, ms 1, r 0, seq 0x2651c16e, mtu 1508 Aug 2 09:00:04.824069 OSPF restart signaling: Add LLS data for DbD packet on interface reth0.0. Aug 2 09:00:04.824107 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Keepalive <Touched> set to offset 40 at 9:00:44 Aug 2 09:00:04.824155 task_job_delete: delete background job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 09:00:04.824185 background dispatch completed job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 09:00:04.824228 background dispatch running job Interface event for task OSPF Aug 2 09:00:04.824257 Interface reth0.0 area 0.0.0.20 event NeighborChange Aug 2 09:00:04.824289 task_job_create_background: create prio 1 job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 09:00:04.824320 Interface reth0.0 (192.168.1.6) area 0.0.0.20 state changed from DR to DR Aug 2 09:00:04.824347 OSPF DR is 192.168.1.6, BDR is 0.0.0.0 Aug 2 09:00:04.825175 OSPF Interface event job processed 1 events. Aug 2 09:00:04.825204 OSPF Interface event job deleted. Aug 2 09:00:04.825228 task_job_delete: delete background job Interface event for task OSPF Aug 2 09:00:04.825253 background dispatch completed job Interface event for task OSPF Aug 2 09:00:04.825298 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 09:00:04.825355 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 09:00:04.825408 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Hold <Touched> set to offset 2:00 at 9:02:04 Aug 2 09:00:04.825439 OSPF neighbor 192.168.1.1 (IFL 67, area 0.0.0.20, rtbl idx 0) set, 40 0 Aug 2 09:00:04.825506 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 09:00:04.825564 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 09:00:04.825613 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Hold <Touched> set to offset 2:00 at 9:02:04 Aug 2 09:00:04.825641 OSPF programmed periodic xmit from 192.168.1.6 to 224.0.0.5 (IFL 67, area 0.0.0.20, ID 0.0.0.0, rtbl idx 0) interval 10 0 Aug 2 09:00:04.825696 background dispatch running job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 09:00:04.825724 OSPF restart signaling: set L bit in hellos sent on interface reth0.0. Aug 2 09:00:04.825752 OSPF sent Hello 192.168.1.6 -> 224.0.0.5 (reth0.0 IFL 67 area 0.0.0.20) Aug 2 09:00:04.825776 Version 2, length 48, ID 192.168.1.6, area 0.0.0.20 Aug 2 09:00:04.825797 mask 255.255.255.248, hello_ivl 10, opts 0x12, prio 128 Aug 2 09:00:04.825818 dead_ivl 40, DR 192.168.1.6, BDR 0.0.0.0 Aug 2 09:00:04.825837 neighbor 192.168.1.1 Aug 2 09:00:04.825858 OSPF restart signaling: Add LLS data for Hello packet on interface reth0.0. Aug 2 09:00:04.825898 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Keepalive <Touched> set to offset 40 at 9:00:44 Aug 2 09:00:04.825947 task_job_delete: delete background job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 09:00:04.825987 background dispatch completed job OSPF PPM processing for task OSPF I/O./var/run/ppmd_control Aug 2 09:00:04.826509 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 09:00:04.826570 task_process_events: recv ready for OSPF I/O./var/run/ppmd_control Aug 2 09:00:04.826619 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Hold <Touched> set to offset 2:00 at 9:02:04 Aug 2 09:00:04.826647 OSPF programmed periodic xmit from 192.168.1.6 to 224.0.0.5 (IFL 67, area 0.0.0.20, ID 0.0.0.0, rtbl idx 0) interval 10 0 Aug 2 09:00:04.864422 task_timer_reset: reset OSPF_Global xmit timer Aug 2 09:00:09.678739 OSPF resend last DBD to 192.168.1.1 Aug 2 09:00:09.678988 task_timer_uset: timer OSPF_Global xmit timer <Touched> set to interval 0.040000 jitter 10 at 9:00:09 Aug 2 09:00:09.679019 task_timer_expire_immediately: timer OSPF_Global xmit timer set to expire now Aug 2 09:00:09.679041 OSPF retransmitting DBD to 192.168.1.1 Aug 2 09:00:09.679080 OSPF sent DbD 192.168.1.6 -> 192.168.1.1 (reth0.0 IFL 67 area 0.0.0.20) Aug 2 09:00:09.679104 Version 2, length 32, ID 192.168.1.6, area 0.0.0.20 Aug 2 09:00:09.679128 options 0x52, i 1, m 1, ms 1, r 0, seq 0x2651c16e, mtu 1508 Aug 2 09:00:09.679150 OSPF restart signaling: Add LLS data for DbD packet on interface reth0.0. Aug 2 09:00:09.679193 task_timer_uset: timer OSPF I/O./var/run/ppmd_control_PPM Keepalive <Touched> set to offset 40 at 9:00:49 Aug 2 09:00:09.679247 task_timer_reset: reset OSPF_DBD rexmit Aug 2 09:00:09.679278 task_timer_set_oneshot_latest: timer OSPF_DBD rexmit interval set to 4.947050 Aug 2 09:00:09.718754 task_timer_reset: reset OSPF_Global xmit timer
Ok milindmistry,
- I removed the area-range from the configuration.
- The physical interfaces between OSPF Neighbors are ge-0/0/4, ge-0/0/5, ge-9/0/4, ge-9/0/5. They all belong to Reth0.
- The status of the command during the OSPF process is
show chassis cluster status Monitor Failure codes: CS Cold Sync monitoring FL Fabric Connection monitoring GR GRES monitoring HW Hardware monitoring IF Interface monitoring IP IP monitoring LB Loopback monitoring MB Mbuf monitoring NH Nexthop monitoring NP NPC monitoring SP SPU monitoring SM Schedule monitoring CF Config Sync monitoring Cluster ID: 1 Node Priority Status Preempt Manual Monitor-failures Redundancy group: 0 , Failover count: 1 node0 100 primary no no None node1 1 secondary no no None Redundancy group: 1 , Failover count: 1 node0 0 primary no no IF node1 0 secondary no no IFI did the traceoptions configuration like requested. Here is the output of the logfile.
↧
↧
Re: SRX 550 - OSPF Adjacency Stuck in ExStart State
Hi,
It looks like both devices are not receiving the DBD packets from the neighbor. SRX traceoptions shows that it is sending DBD packets (mtu 1508) multiple times but not receiving any DBD packets from the neighbor. DBD packets are unicast packets.
Are you able to ping SRX to Brocade and Brocade to SRX? Also check the ARP entry for the neighbor ip.
ping 192.168.1.1 source 192.168.1.6
show arp no-resolve
monitor traffic interface reth0.0 no-resolve detail matching "proto 89"
↧
Re: IS-IS run over GRE
Hi Kingsman
I also thougnh about that. But even increased MTU to 1516. Still don't come up.
Thus, I don't get what happen to this status.
And one side don't have any traffic while I used "monitor traffic interface gr-5/0/0.1" on both side.
> show configuration interfaces gr-5/0/0
unit 1 {
tunnel {
source 62.115.162.53;
destination 218.30.53.190;
}
family inet {
mtu 1516;
tcp-mss 1436;
address 172.54.129.50/30;
}
family iso {
mtu 1516;
}
family mpls;
}
Best regards,
Cloud
↧
Re: IS-IS run over GRE
Hi,
Is ospf working fine on same interface unit number - gr-5/0/1 unit 1?
↧