Re: Filter Based Forwarding on SRX
Hi Steve, Thank you for your help. I configuread RPM and IP-Monitoring as in the link and it's all now working. Thank you again for your help. Much appreciated Adrian
View ArticleRe: Forwarding/Static Route between logical interfaces on one J-series router
The J-series devices have the firewall flow based zone rules for traffic by default. So you have three options: 1-Write policies and put the interfaces into zones that permit the traffic to flow...
View ArticleRe: PEM 0 not OK MX104
If they are using DC power supplies this is a known issue on PR 1064039 where the fans do not detect the temperature correctly and fail to cool the power supply causing the shutdown to occur. This is...
View Articleshow ospf route .. Route Type Network vs Router
DearsHope you are doing great. Need your assistace please regarding below command R1> show ospf route router Topology default Route Table:Prefix Path Route NH Metric NextHop Nexthop Type Type Type...
View Articleshow ospf route .. Route Type Network vs Router
DearsHope you are doing great. Need your assistace please regarding below command R1> show ospf route router Topology default Route Table:Prefix Path Route NH Metric NextHop Nexthop Type Type Type...
View ArticleRe: show ospf route .. Route Type Network vs Router
First of all, there is no level-1/level-2 in OSPF, only in IS-IS. :-) Back to your question:(1) The Path Type is either Intra (type-1/2 LSAs), Inter (type-3 LSAs) or Ext1/2 (type-5/7 LSAs - depending...
View ArticleRe: Forwarding/Static Route between logical interfaces on one J-series router
Ah! That was it! Thank you!!
View ArticleClik here to view.
Re: show ospf route .. Route Type Network vs Router
Thanks Carsten for your reply For ISIS levels yes it was a mistpe One more thing why then Network appears with External (LSA-5) appears ? Many thanks Best RegardsSherif Ismail
View Articlecan bandwidth command affects QoS
http://www.juniper.net/documentation/en_US/junos14.2/topics/usage-guidelines/interfaces-configuring-the-interface-bandwidth.html I only saw it will affect OSPF cost, not sure if can affect QoS.
View ArticleRe: PEM 0 not OK MX104
Hi Steve, Thanks a lot for your feedback. Actually we have version 15.1R2.9 running (Domestic version).Is it only resolved on 13.3R7 or on all versions after that including version 15.1? Does domestic...
View ArticleRedistribution of static routes in VR configuration into OSPF
Hi, my config looks like this:set routing-instances VR_Office routing-options static route 10.14.0.0/16 next-hop 10.181.101.249set routing-instances VR_Office routing-options static route 10.14.0.0/16...
View ArticleRe: Redistribution of static routes in VR configuration into OSPF
Stefan, in my environment your configuration works as expected. So, either software bug or something else in the configuration (e.g. stub area?). Cheers,Carsten
View ArticleRe: Error (code: 1219, type:Major) encountered, cmalarm_passive_alarm_signal
The reffered link is for ECC errors and not for the asked question. This one is for packet...
View ArticleRe: PEM 0 not OK MX104
Looks like they show it resolved in your version. So yours must be a different issue. https://prsearch.juniper.net/InfoCenter/index?page=prcontent&id=PR1064039 Resolved In13.3R7 14.1R6 14.2R5...
View ArticleForce traffic from Self to avoid routing table. SSG
Hi everyone, Here is my situation terse : set route 0.0.0.0/0 interface ethernet0/0 set VPN1 outgoing-interface "ethernet0/0" /same peer for both set VPN2 outgoing-interface "ethernet0/3" /same...
View ArticleRe: Force traffic from Self to avoid routing table. SSG
You will need to move the interface eth0/3 into a separate virtual router with its own default route. By default all the interfaces are in the same virtual router and share the same routing table. If...
View ArticleRe: Redistribution of static routes in VR configuration into OSPF
Thinking helps... sometimes. No external LSAs in stub areas. :-)
View ArticleSource based default route
Server---->Ex4200--------->ISP1 | ---------->ISP2 Can I do filterbase forwarding on the basis of BGP community? I already do this with...
View ArticleRe: Source based default route
The firewall filters are executed on the data plane and therefore are able to match on anything which is carried inside the packet (src/dst IP address, src/dst port, protocols, etc.). BGP communities...
View ArticleRe: Source based default route
is there any way to change default route via remotely? Filter is not neccessery if I have diffrent way to do this?
View Article