Re: Source based default route
Not sure what you mean by "change default route remotely"? Change the next-hop? Well, this could be done via BGP. But maybe it's easier to describe your requirements exactely first (like which device...
View ArticleRe: Source based default route
I need to send some of traffic to specific ISP. If some routes has xxx:xx community send return traffic to ISP2 User IP(192.168.2/30) Default route of Ex4200 is 0.0.0.0/0 next-hop ISP1 I added...
View ArticleMX240 Enhanced MX SCB 2
We have new MX240 with two routing engines. Each routing engine has a card (XGE) with twp SFP ports.. I think they are the CB 0 and CB1. We don't see those 4 interfaces when we issue "show interfaces...
View ArticleRe: LDP-tunneling over RSVP in multi-area ospf network
Hello, In order for r4 to consider r3's loopback, or any other address redistributed by r3, is reachable via an rsvp lsp it checks it's ospf database. The issue here is that the routes from r3 are...
View ArticleRe: MX240 Enhanced MX SCB 2
You cannot enable those two 10G ports. They are for future use. Cheers,Carsten
View ArticleError message after upgrade MX-5 to version 13.3R8.7
After upgrading to version 13.3R8.7 following message is flooding in the message log Apr 2 02:12:14 mx-1 tfeb0 Reset media mux for mic slot 1Apr 2 02:12:14 mx-1 tfeb0 PQ3_IIC(WR): no target ack on...
View ArticleRe: Error message after upgrade MX-5 to version 13.3R8.7
it is HW issue , and in most cases it is RMA . Try to open case to JTAC
View ArticleRouting Issue
I have a EX3300 hanging off a FIOS router (192.168.1.0/24), I have the 192.168.1.0 network routable from my internal networks (10.10.10.0/24 & 10.10.110.0/24) as I have a port configured as an...
View ArticleRe: can bandwidth command affects QoS
There are two ways to configure the bandwidth for OSPF to use. One is directly on the interface which would affect the CoS and OSPF. The second is reference-bandwidth. Configuring the...
View ArticleRe: Routing Issue
You didn't say in your post whether the 192.168.1.99 address is bound to a VLAN interface or a logical unit on the EX3300. To make your scenario work, you'll need to attach it to a vlan interface, and...
View ArticleRe: Routing Issue
Ben, Thank you for the reply.the port is configured as an access port with no VLAN associated. on either the routed uplink or the NAS port. Thank you,Bill S.
View ArticleRe: Routing Issue
Below is the current switch configuration: ## Last changed: 2016-04-03 00:26:03 EDTversion 12.3R12.4;system {host-name junos1;domain-name gsf.home;domain-search gsf.home;time-zone...
View ArticleRe: Routing Issue
Okay, so in a nutshell you would need to do: delete interfaces ge-0/0/12.0 delete interfaces ge-0/0/10.0 set vlans v11-FIOS description "FiOS Network" set vlans v11-FIOS vlan-id 11 set vlans v11-FIOS...
View ArticleCisco reflexive access list
I'm trying to convert Cisco configuration to Juniper MX configuration.. On Cisco device there's a reflexive access list.. Anyone knows what's the equivalent commands in Juniper ip access-list extended...
View ArticleSRX220's - OSPF interrupted during configuration commit
We are deploying several hundred SRX220's (v12.1X46-D40.2) out across our enterprise campus which all come back to our central datacenter via VPN. We run OSPF out over the VPN link and basically...
View ArticleRe: MX960 w/trio cards - QoS across AE?
Hi, There is only workaround... I.e. do the active and standby kind of configuration under ae interface with lacp with 2 member links. Through which you can achieve your objective.Regards,Vinay
View ArticleOSPFv3
Hi , I am new to the j-community so I hope i post in the cprrect place would you mind explaining to me how OSPFv3 " Link LSA " improve efficiency I was a Cisco guy :'3 Many thanks in Advance
View ArticleRe: SRX220's - OSPF interrupted during configuration commit
Hello,It looks like You are using very short OSPF timers.And please post Your sanitized config.HTHThxAlex
View Article