Re: What commands are used to show vlan status and config in MX960?
Hi eesunj, You will find the below kb useful;https://kb.juniper.net/InfoCenter/index?page=content&id=KB26487&actp=METADATA Also commands like below should be useful;>show vlans>show...
View ArticleRe: What commands are used to show vlan status and config in MX960?
Thank you so much for your reply. the link is good, but show vlans commands cannot work in MX960.This command can tell a lot info: AB> show bridge ? Possible completions: domain Show bridge domain...
View ArticleMX480 with Junos 16.1R2 what does log message mean
Getting the log on MX480 with JUNOS 16.1R2, just want to whats this log mean and what will be impact if this continous on box #show log jam_chassisd Apr 4 11:56:30 jam_cache_get.636 ERR:entity 0x997...
View ArticleRe: Flowspec Actions supported?
I heard back from our SE that remarking isn't currently supported, so we'll have to use something like DCU if we want to accomplish that last bit.
View ArticleThe VPN is up, but I have no access on servers
Hi! I just configure a site-to-site vpn. Both Phase 1 and Phase 2 are UP, but I can not access any servers.Does anyone have any tips to help me?TKS! Source network: 192.168.4.0/23Remote network:...
View ArticleRe: The VPN is up, but I have no access on servers
Hello, bruno300! I hope you're having a great week.Thanks for posting so much helpful information. I have a few recommendations. First, run a continous ping to a server on the other side then run the...
View ArticleSNMP monitoring of a FPC inline-services flow-table-size
Hi All, Not quite sure if this question should be posted under 'Management' instead but as it relates to an MX I am posting it here. Please look at the following configuration snippet of an MX960...
View ArticleClik here to view.
Re: The VPN is up, but I have no access on servers
Hi synackray!Thank you very much for the information.I performed all the procedures you reported. Unfortunately I am not a firewall expert and it's the first time I'm configuring a juniper equipment,...
View ArticleRe: SNMP monitoring of a FPC inline-services flow-table-size
Also, if it helps, the data that we need to check is contained under the following FPC shell output: FPC1(blah.blah vty)# show jnh 0 inline-services flow-table-info
View ArticleRe: The VPN is up, but I have no access on servers
Hi, bruno300! I have good news and bad news. Based on the logs you've provided your device is generating the requested ping, it passes all policy checks, and it is sent out of st0.0. However, in your...
View ArticleFilter allow traffic or routes into router?
Hi Anyone can explain the below? the config allows traffic go into router or allow routes go into router if they attach interfac ge-1/1/5 in MX960? set firewall family inet filter Vendor4 term Evc...
View ArticleRe: Filter allow traffic or routes into router?
"set firewall family inet filter Vendor4 term Evc from destination-address 6.17.18.247/32set firewall family inet filter Vendor4 term Evc from destination-address 6.17.18.247/32set firewall family...
View ArticleRe: Filter allow traffic or routes into router?
Thank you for your reply. I know routes, instead of data traffic, will be sent out/in if we use bgp policy like the below: set routing-instances WWA protocols bgp group VV6 import RV6set policy-options...
View ArticleRe: Filter allow traffic or routes into router?
Please find answers inline: /So, can we say data traffic would be sent out/in only when the prefix is attahced in physical interface?/ -Yes you are correct, by attaching to physical interface we...
View ArticleIs there any way to configure phase 1 in Juniper SRX 340 without using DH...
Hi! I'm trying to configure a site-to-site vpn with another location that uses a CISCO ASA equipment.The ASA is configured to not use DH Group and my Juniper SRX 340 is configured as DH Group 2, thus...
View ArticleRe: Filter allow traffic or routes into router?
"For example , we can control(allow/deny) updates from a neighbor as whole"I think the "updates" you mentioned above should be route, or prefix, right?
View ArticleRe: The VPN is up, but I have no access on servers
TKS for support synackray!The problem was solved, it was in peer device ! Tks!
View ArticleRe: Is there any way to configure phase 1 in Juniper SRX 340 without using DH...
IMO it's mandatory to have DH in phase1.I recall you had a problem with phase2 establishment in another topic Are you really sure it's ph1?Usually you can choose not to enable PFS in ph2
View ArticleRe: Filter allow traffic or routes into router?
Yes it is control plane route/prefix updates . Please mark this as accepted solution , if it answers your query
View ArticleNo Resources Issue in MX-BRAS
Hi, I face an issue that needs for advise. I have configured the MX-104 as a BRAS with the attached configuration. when I try to initiate a PPPoE session from any PC to this router I get this error...
View Article