Re: OSPF routing issues
Hello,We need to see Your configs, but OSPF DN-bit set in LSA3 by PE-1 would have prevented this:simpnet wrote: Due to route preference (AD), OSPF route is preferred on PE-2 which it then advertise...
View ArticleRe: OSPF routing issues
Hi aarsenlev, Thanks for looking into this. As requested, please see the configurations below.================PE-1 Configurations=================set routing-instances VRF-LAB instance-type vrfset...
View ArticleRe: J2320 - V12.4 BGP And Firewall Setup
hi, Still no joy, appears that source IPs are being ignored and the global deny policy then denies those connections coming in. What is odd is that we can see two to three devices connect fine from...
View ArticleRe: OSPF routing issues
Hello,In Your OP You mentioned "OSPF" which usually means "OSPFv2" RFC 2328.However, Your configs show You are using OSPFv3.The DN-bit for OSPFv3 is described in RFC 6565...
View ArticleRe: OSPF routing issues
After a few permutations and combinations, I have found a workaround for this. Basically, I forced all BGP routes imported on both PE-1 and PE-2 within the "VRF-OSPF" routing instance to have a...
View ArticleRe: can i map 7 channelized stm1s to STM16 port on MX960?
Sorry, I've never used multiplexing like that before. But from the MX side if the ADM is working correctly we should see a single STM16 port configuration. The question is really to the ADM vendor on...
View ArticleRe: J2320 - V12.4 BGP And Firewall Setup
To see why the policies are not working we will need the source and destination ip addresses to evaluate the configuration. If you could run trace options per this and post the file it would help too....
View ArticleInteresting routing issue
Hi all, Set up as follows: RADIUS --> SRX --> MX240 (Core) --> MX240 (LNS) Radius Server has 1 port and the gateway is the SRX Ge port. The SRX Xe port connects to the MX240 (Core) 10g port...
View ArticleRe: Interesting routing issue
What is the source IP address you are using for your pings to the RADIUS address ..?
View ArticleRe: Interesting routing issue
do you have any routing-instance configured on the box? do you see the route to reach Radius in global routing-table or in instance?No route to host usually comes when you don;t have route to reach the...
View ArticleRe: Interesting routing issue
Hi, Its good if you can share your interested config and relative logs/ping.
View ArticleRe: RE-S-2000 with 16.1 R5 ??
Yes, You can use 32-bit image to install Junos 16.1R5 [KUDOS PLEASE! If you think I earned it!If this solution worked for you please flag my post as an "Accepted Solution" so others can benefit..]
View ArticleRe: L2_BRIDGE family extension message
Hi, Interface ae5.3 has ifl number 461 , the logs you are receiving is for ifl 429 . Can you please check which interface has ifl 429 ?
View ArticleRe: Interesting routing issue
Apologies, yes, I should have show the config. I will get that information and let you know.
View ArticleRe: Interesting routing issue
Strangely, after changing absolutely nothing, ping now works as well.... So, traceroute is goodPing is goodRouting table is good all is good....
View ArticleRe: BGP peering via (allow) not working
Hi @singhh Kindly I activated tracoption for this group with (allow) and have the following:Local: 10.93.192.5Remote: 10.254.11.6Command allow 10.254.11.0/24 Sep 29 12:42:36.420915 BGP SEND...
View ArticleRe: BGP peering via (allow) not working
mkhachfeh wrote:Hi @singhh Kindly I activated tracoption for this group with (allow) and have the following:Local: 10.93.192.5Remote: 10.254.11.6Command allow 10.254.11.0/24 I saw that subcode 3 means...
View Article