support of Inline Active flow monitoring on MS-MIC with Junos 14.2 and Junos...
Hi All,one of my customer having MX-480 & MX-960 and they want to use MS-MIC for inline active flow monitoring on each box. Junos version is 14.2 and they want to use Junos traffic vision V9...
View ArticleRe: support of Inline Active flow monitoring on MS-MIC with Junos 14.2 and...
Hi Badar, We can do flow monitoring using the below methods in junos: 1. Inline active flow monitoring is implemented on the Packet Forwarding Engine on the FPC.2. Active flow monitoring is using...
View ArticleRe: Inject L2TP pool into isis
Hi Rahul, Thought it may be appropriate here to post a warning regarding the configuration used: It appears that although everything seems to be working perfectly there was a slight issue that I had:...
View ArticleISIS Export Policies (Policy-Options)
Hi, Set up: Laptop -> Cisco 1841 (PPP PAP client) -> Cisco 1841 (LAC) -> Juniper MX240 (LNS) -> MX240 (Core) -> SRX1500 -> RADIUS When powering up all the devices I get an L2TP tunnel...
View ArticleRe: ISIS Export Policies (Policy-Options)
As an add on to this, with a little more information...... I believe that the required network advertisements will take place via BGP once it is configured, but I cannot do that yet until it is...
View ArticleRe: ISIS Export Policies (Policy-Options)
Hi, For every PPP subscribers terminating on LNS there will have access-internal route. We redistribute the same using export policy.Not sure why you need instance master for redistributing subscribers...
View ArticleRe: ISIS Export Policies (Policy-Options)
Hi Rahul, Our end resolution, as we have already diuscussed, is that we will supply the CPE (or CE) with the following configuration: CE to Provider Edge -- IPv6CE facing customer circuits - IPv6 and...
View ArticleMulticast Routing - MPLS + EVPN + MVPN
Hello All,I have two EX9200's directly connected (P+PE/CE in one) with MPLS and the EVPN overlay protocol enabled.On EX9200-1 i have an external connection (ge-0/0/2) with several multicast sources....
View ArticleMX irb and SRX reth Issue
Hi All,I am struggling being able to configure the irb on my MX104 to be able to ping across to my reth on my SRX240H2. See the following configurations, but do note that since I am building this out...
View ArticleRe: ISIS Export Policies (Policy-Options)
Hi Rahul, Strangely all the routes have come back now....As mentioned, I need to test IPv6 and as such have changed my pool address assignment from IPv4 to IPv6 as per below: I removed these...
View ArticleRe: ISIS Export Policies (Policy-Options)
Here is my current configuration. Juniper does not make it clear in its website reference IPv6 configuration: set dynamic-profiles dyn-hex-lns-profile routing-instances "$junos-routing-instance"...
View ArticleRe: MX irb and SRX reth Issue
Hello,RETH is not supported on standalone SRX. You have to have a SRX cluster built first.HTHThxAlex
View ArticleRe: MX irb and SRX reth Issue
Hi Alex, Thanks for the response. The reth is indeed configured on an SRX cluster. I was under the impression I could deploy a reth on a cluster with a single physical interface in the reth. Is this...
View ArticleRouted VPLS in Juniper
Dear Experts, I need to interoperate NOKIA (Alcatel-Lucent) and Juniper (I believe SRX) On Nokia I am running routed-VPLS. Can I do that on Juniper? Cisco can do it as well. I read somethig about VPLS...
View ArticleRe: Routed VPLS in Juniper
with routed-vpls we communicate internally both VPLS and VPRN without needing an external hairpin.
View ArticleRe: MX irb and SRX reth Issue
In case this is needed: MX version: root> show versionModel: mx104Junos: 13.3R1.8JUNOS Base OS boot [13.3R1.8]JUNOS Base OS Software Suite [13.3R1.8]JUNOS Kernel Software Suite [13.3R1.8]JUNOS...
View ArticleRe: Routed VPLS in Juniper
Hi, This is possibe by configuring an irb routing-interface on the vpls instance and then the same irb interface can be added to any RIs/vrfs.set routing-instances <vpls> routing-interface...
View ArticleRe: MX irb and SRX reth Issue
Have you configured reth-count using command,"set chassis cluster reth-count 15"..Also, if you configure and still it is not working, you add following command.."set interfaces reth2...
View ArticleRe: ISIS Export Policies (Policy-Options)
Hi, You need following configuration to bring IPv6 up. Hope you're requesting only NDRA prefix. Define family IPv6 and RA under Dynamic-profile. LNS# show dynamic-profiles dyn-lns-profile | no-more...
View ArticleRe: Part Number verses Model
You could also see if this command gives you the model numbers that match your inventory system. show chassis hardware models
View Article