Re: LDP over IPv4/IPv6
Hi, Because I tested on the same router. Therefore,I used logcial system for establising. My backbone used OSPF3 as IGP for IPv6 and the neoghbor of OSPF is up.> show ospf3 neighborID Interface...
View ArticleRe: LDP over IPv4/IPv6
Well, it should have taken ipv4 by-default but glad to know that after hardcoding the transport address, it worked for you.
View ArticleRe: LDP over IPv4/IPv6
Hi,As I understand from the documentation, by default the transport mode is IPV6. You need to explicitly configure transport-preference as IPV4 if you want TCP session for IPV6 over IPV4 transport. You...
View ArticleRe: LDP over IPv4/IPv6
Hi, I meant with the transport-address and Just to add for the people who read this thread. It can work without setting the transport-preference as well. just need to make sure that your transport...
View ArticleRe: LDP over IPv4/IPv6
Hi, I think my IPv4 filter will allow ldp going through successfully. So, it is working once "transport-preference ipv4" is done. The first thing what I need to do is checking my IPv6 filter and see...
View ArticleRe: how to delete regular communities
Interesting attempt, but not acceptable by Junos:[edit policy-options community all-standard members] '*:*:*' Unknown extended community type error: configuration check-out failed
View ArticleRe: VRRP across two locations
Hi and thank you for replying.I would agree with your suggestion, but if I configure an irb within the VPLS instance as a routing-interface, this would affect only one MX router, the other would not...
View ArticleRe: VRRP across two locations
Hi,You can configure IRB as routing-interface on both MX routers. You can use different IPs but put all the IRBs in the same subnet. Something like this:MX1---irb.1(10.10.10.1/24)|...
View ArticleRe: how to delete regular communities
Humm okay, didn't had the device handy for a quick test.Regards,Amit
View ArticleInter vrrp-group routing
Hi All,We are working on a migration project from Cisco to Juniper, under the Cisco devices, the HSRP groups were configured on a single interface and all could talk across to each other. After...
View ArticleVPLS neighbor at global and mesh-group
Dear all. I want to ask the difference between setting up a neighbor at global and setting up a neighbor in mesh-group. I have a configuration like this root# show routing-instances VPLS_TEST...
View ArticleProblem about Juniper EX4500
I have a Huawei S6720 and Juniper EX4500 interconnected through WDM device, the two port of WDM are normal in transceiving light, 2-terminal equipment modules are also normal in transceiving light, the...
View ArticleRe: Inter vrrp-group routing
Hi, When you say on Cisco you had all the groups under one interface, what interface type was that? By inter-group communication, I guess you mean inter-vlan communication because all the logical units...
View ArticleRe: Problem about Juniper EX4500
Hi, Sounds like a classic link flap. Couple of checks to narrow down which device causes the link to flap/interface up/down/up condition. 1. When you get to know that link/interface went down &...
View ArticleAuthentication Algorithms
Hi, i cant seem to find SHA384 authentication under ipsec configuaration. The VPN devices both checkpoint and Foritgate support this in phase2. Am i missing something?
View ArticleRe: Authentication Algorithms
Hi,This is what I can see from the documentation:SHA-256, SHA-384, and SHA-512 (sometimes grouped under the name SHA-2) are variants of SHA-1 and use longer message digests. The Junos OS supports the...
View ArticleRe: Inter vrrp-group routing
Hi there,The cisco HSRP config is attached. This is a single VLAN, running 3 broadcast domains with a primary and 2 secondary IPs. What I mean is for an IP in the primary IP subnet to be able to...
View ArticleRe: VPLS multihoming
Hi Karan, BFD sounds like a possible way to do it. But as you say I need to make sure the customer network supports it. Not sure about that but I will investigate it. Thanks! Erac
View Article