how to delete regular communities
How to delete regular (common) communties and leave extended in the routes?I need to set regular community. Set means that all other regular communities should be deleted. But extended should be...
View ArticleLDP over IPv4/IPv6
Hello My backbone is dual stack over IPv4 & IPv6. And IPv4 is running on MPLS/LDP.Now I hope that IPv6 can run onMPLS/LDP. After refer to the document as follow. I still can't do it successfuly.Do...
View ArticleRe: LDP over IPv4/IPv6
Can you paste your LDP configuration? And show version output?[edit]root@PE1_re# run show ldp neighborAddress Interface Label space ID Hold timefe80::5668:a3ff:fe1a:37e0 ge-0/0/3.0 172.16.0.22:0...
View ArticleRe: LDP over IPv4/IPv6
Hello Kingsman Thanks for your reply. As attachment is my configuration.If I remove IPv6 on LDP, the LDP session over IPv4 will be normal as follow. > show ldp neighborAddress...
View Articleaddress-book & address-set equivalent in MX for firewall filters
Hello community,Might be a naive question but, how can we make named groups containing prefixes and other named groups in junos under MX?The closed example is what we have in SRX as address-book &...
View ArticleRe: address-book
Hi,,You mean this?[edit]root@PE2_re# set policy-options prefix-list test 10.0.0.0/24[edit]root@PE2_re# set policy-options prefix-list test 10.0.1.0/24[edit]root@PE2_re# set policy-options prefix-list...
View ArticleRe: address-book
Hi, That is what I'm doing so far. But what a I want is to use nested groups of prefixes like we have in the srx.ExampleSYSLOG-SOURCES |-> SYSLOG-NYC (inside tis group, defined 3 prefixes)...
View ArticleRe: how to delete regular communities
Hi! There is no direct way to remove only standard community. The correct way of achieving is what you are already trying, using regex match condition. You need to sort more details what all...
View ArticleRe: how to delete regular communities
Hello,This is pretty easy if You remember how JUNOS evaluates communities (hint-they are treated as strings): Community regular expressions evaluate the string specified in term on a...
View ArticleRe: /31 prefix for BGP
@karand, 60.60.60.1 would be on a different subnet from 60.60.60.2. Your neighbor has to be 60.60.60.3 if your IP is 60.60.60.2/31.
View ArticleRe: address-book
You could reference more than one prefix list to accomplish the same thing: set firewall family inet filter TERM1 term IN-Allow-SYSLOG from destination-address 148.64.56.88/32set firewall family inet...
View ArticleRe: /31 prefix for BGP
Using a /31 subnet mask helps conserve your IP address space for point to point links.It doubles the number of links that you can number from a given block of IP addresses.If you think of large...
View ArticleVRRP across two locations
Hello, Background: I have two datacenters, located 300km apart each with a Juniper MX240 router connected over a DWDM 10GE link. The latency is the range of 5ms RTT. In each datacenter, I have one...
View ArticleRe: LDP over IPv4/IPv6
Hi Kingsman Sorry to reply so late. As enabled traceoption, I only saw some log as below. Should I enable "family iso " ? Feb 2 10:16:15 trace_on: Tracing to "/var/log/ldp" startedFeb 2...
View ArticleRe: VRRP across two locations
Hi, You can probably configure VPLS between 2 MX240s and call irb as a routing-interface inside that VPLS instance. Also you can then configure 2 irbs on MX240 and reth(irb) interface on firewall with...
View ArticleRe: JUNOS behavior on BFD remote discriminator change whist session is active
Hi, If firewall is in active/passive mode, I assume routing information is not in sync between master and backup firewall. In that case, IMO, the existing BFD session with old descriminator should go...
View ArticleRe: LDP over IPv4/IPv6
Hi, Sorry, but had few questions to clarify: 1. As I understand your core interfaces are on rlt- right? What IGP protocol you are running here? Do you have the corresponding IGP session up? If you are...
View Article