SNMP OID for Route Table Size
Looking for the OID for the route table size. MX480 on 15.1R6.7 IPv4 Route Tables:Index Routes Size(b)-------- ---------- ----------Default 725254 98634540 I want the second...
View ArticleRe: SNMP OID for Route Table Size
Hello,JUNOS supports IP-FORWARD standard MIB (RFC 4292) and this MIB has inetCidrRouteNumber OID:https://tools.ietf.org/html/rfc4292 inetCidrRouteNumber OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only...
View ArticleVoice getting stop during call in networks
As per my networksTopology:IP phone>>>>>>>EX4300 switch (Before Core)>>>>>>>>>>>>Core_EX4500...
View ArticleWeird NTP issue with MX960
Hi All, I am working on a project right now with MX routers. Of all of them, there is one, an MX960 that seems to have trouble keeping decent time. It has three stratum 1 upstream time servers...
View ArticleRe: SNMP OID for Route Table Size
Hi Folks,Please find some pointers on Using the Enterprise-Specific Utility MIB to Enhance SNMP Coverage, you can try exploring on that front,...
View ArticleRe: Weird NTP issue with MX960
Strange. Can you failover to the other re?Then we can see if the issue is hardware or configuration related. Seems unlikely two re would fail in the same way.
View ArticleL2CKT offset
Asking a very basic question, can someone please explain what does offset means in the show route for L2Cicuit labels in mpls.0: 299776 *[L2CKT/7] 02:03:21 > via...
View ArticleRe: L2CKT offset
Hello,Looks like You have L2circuit with Control Word enabled, hence the payload Ethernet frame starts after VC label + 4 Byte offset .Please post the printout:show l2circuit connections | no-more- to...
View ArticleIPsec in our new juniper MX480 router (MS-MIC/MS-MPC cards)
Hi Guys,I need to configure IPsec in our new juniper MX480 router.My doubt , is it possible to configure the same without MS-MIC/MS-MPC cards.If so please guide me to configure the same or share me any...
View ArticleProblem with media converter on Junos 15.1R6.7
Hello,We recently upgrade to Junos 15.1R6.7 version in our MX960 and an interface link change to DOWN. We didn't change the configuration, we just upgrade from version 12 to 15. The rest of the...
View ArticleRe: Problem with media converter on Junos 15.1R6.7
Hello, wrote: This link connects physically to a media converter from ethernet to fiber, and then connect through level 3 to another router. We solve this issue connecting a hub between our MX960 and...
View ArticleRe: IPsec in our new juniper MX480 router (MS-MIC/MS-MPC cards)
Hello, wrote:Hi Guys,I need to configure IPsec in our new juniper MX480 router.My doubt , is it possible to configure the same without MS-MIC/MS-MPC cards. Short answer is no.Long answer is You can...
View ArticleClik here to view.
Re: Problem with media converter on Junos 15.1R6.7
It's not exactly a hub, it's a dumb switch.Without the switch, the link is DOWN. Everything was UP before the upgrade. The interface configuration is:ge-1/0/3 { enable; speed 100m; mtu 9192; link-mode...
View ArticleDDOS attack prevention in MX series Routers
Hi Friends, Anyone please help me to configure MX104 & MX480 routers for preventing syn flood, icmp flood (DDOS Attacks).Also please share me sample configuration for same if available. Thank you
View ArticleRe: DDOS attack prevention in MX series Routers
Please check below config example.https://www.juniper.net/documentation/en_US/junos/topics/example/subscriber-management-ddos-example.html
View ArticleRe: Problem with media converter on Junos 15.1R6.7
Try turning off auto-neg on the port in addition to the settings you have for 100 full explicit and see if the link will come up. Also what is the card on the MX can the optic from the media convertor...
View ArticleRe: RSVP hello failed on the interface with two addresses
Hi, You have pasted the session output, but what is seen in "show rsvp neighbor" output? Can you try putting "primary" keyword under the address which you want to prefer for forming RSVP session? "set...
View ArticleRe: DDOS attack prevention in MX series Routers
Hi,Here are additional links for your reference:...
View ArticleRe: Weird NTP issue with MX960
This was a good suggestion.After switching the routing engines, all heck broke loose with NTP times. The backup routing engine I don't think had been NTP synced in ages, if at all, so it was wobbling...
View ArticleRe: Weird NTP issue with MX960
"That reset the clock back to accurate, but ..." ...it quickly drifted back to 55ms off and stayed there.
View Article