Re: Multipath in vrf routing-options
Inet.0 entry is sufficient for igp metric comparison .
View ArticleClik here to view.
ibgp and route reflector
Hi Guys I am seeking your kind advice for some topology that i am doing in a lab.Below i s the drawing of the lab. There is 2 RR, called RR1 and RR2, and RRC1 and RRC2. RR1 is having an ibgp to...
View ArticleRe: Blackholing and Rate Limiting for DDOS
think you can read up about flowspec if this is what you are looking for
View ArticleRe: ibgp and route reflector
It seems you are confused about where to configure the cluster-id. The cluster-id has to be configured on the route reflector not on the clients. From a configuration point of view, a client does not...
View ArticleRe: ibgp and route reflector
the cluster-id is configured at the router reflector, the cisco is just a client of the juniper.
View ArticleRe: ibgp and route reflector
I beleive RR1 and RR2 are non-client to each other .. In RR2 ,Can you configure "keep all " knob under neighbor stanza for the neighbor RR1[edit protocols bgp group group-nameneighbor 100.1.1.1] and...
View ArticleRe: ibgp and route reflector
HI, I didn't quite understand from the picture which are RRC1 & RRC2 but assume they are the red routers.Also assume that RR1 & RR2 are configured with the cluster IDs to be acting as RRs....
View ArticleiBGP to OSPF Redistribution
Dear Members;i want to redistribute a specific prefix from iBGP to OSPF (am also redistributiong from OSPF to iBGP on the same router but for different prefixes), but the prefix does not show in OSPF...
View ArticleRe: iBGP to OSPF Redistribution
Can you share the relevant topology as well , so that its easier to triage
View ArticleRe: iBGP to OSPF Redistribution
Hi, Could you share the config for better understanding.I assume the policy is applied as export to ospf and the prefix is active as BGP route in the routing-table.You could verify the policy...
View ArticleJ-flow licensing on MX104
Hi, maybe a dumb question but here goes :-) I'm currently looking at some MX104 licensing and I'm not sure how to read the limitation for the 5G/10G J-flow licensing. When looking at the description...
View ArticleRe: iBGP to OSPF Redistribution
Thank you for you replies guys....actually the reason why iBGP isn't redistributing into IGP is that this redistribution is not allowed by default.......
View ArticleRe: iBGP to OSPF Redistribution
Hi, This command is for JunosE.AFAIK, a BGP route should be able to be exported to OSPF with an export policy by default [i.e no additional tweaks required]. Cheers,Ashvin
View ArticleRe: iBGP to OSPF Redistribution
Heve you applied export/import policy in protocol configuration? Show your BGP,OSPF and policy configuration.
View ArticleRe: One VPLS instance for multiple VLANs
Hi, I believe it would work as well as when the vlan-id is specified in the VPLS routing-instance [VLAN Normalization]. I have tested this successfully.Sample config:---------- PE1 -----------...
View ArticleDynamic GRE tunnel failover and load balancing and tunnel services
Hi Folks , In case we have tunnel service enabled on 2 FPC's , ( MPC3E and MPC 3D 16x10GE ) is there some logic for selecting an FPC to create the gr- tunnel interface ?In the lab we...
View Articleflow-tap data rate
I found this reference in the below document. Is it correct that this is a current limitation of flow-tap (about 40 Mbit/sec) “For flow-tap, a services PIC supports a total limit of 20 Kpps ingress...
View ArticleRe: flow-tap data rate
This limitation only for M/T series which need a service pic (AS or MS) for LI. MX do LI inline with tunnel services. rate and number of filters are much better
View ArticleMemory issue on MX480
Hi,we use dual RE-S-2000 on MX480 with JUNOS 13.3R9.13 and we have memory over 70% with OSPF, LDP, BGP in dual stack. Below few other info about the status.Can you help me to reduce the memory...
View Article