Quantcast
Channel: All Routing posts
Browsing all 8688 articles
Browse latest View live

Re: ISIS Attached Bit questions

Hello Gongyayu On the vmx nodes are you running the isis inside a vrf or in the global routing instance ?Also both the vmx1 and vmx3 are level 1 only and still you are seeing the attached bit right ?It...

View Article


Re: ISIS Attached Bit questions

Hello,  wrote: I captured LSP packets on vMX1 interface ge-0/0/1 facing vMX3. I got the following two LSP packets. One has attached bit on, the other has attached bit off. They have differnet LSP_ID I...

View Article


Re: ISIS Attached Bit questions

vMX1root@vMX1# show | display setset version 14.1R1.10set system host-name vMX1set interfaces ge-0/0/0 unit 0 family inet address 10.10.4.11/24set interfaces ge-0/0/0 unit 0 family isoset interfaces...

View Article

Re: ISIS Attached Bit questions

thanks so much !!!

View Article

Re: ISIS Attached Bit questions

Hi Gongyayu You will see the attached bit in the cases where either you are having ISIS connections inside of a routing-instance or a logical system. If you have isis L1 only adjacency between to...

View Article


Re: ISIS Attached Bit questions

Hello,  wrote:Hi Gongyayu You will see the attached bit in the cases where either you are having ISIS connections inside of a routing-instance or a logical system. It does not matter, ISIS adjacency in...

View Article

Image may be NSFW.
Clik here to view.

Can you configure the forward address in Juniper for Type 5 (external) LSAs?

Does Juniper allow you to configure the Type 5 (External) LSA forward / forwarding address?I can't seem to find it anywhere in the documentation (granted the documentation library is huge, as is the...

View Article

Re: Can you configure the forward address in Juniper for Type 5 (external) LSAs?

Hello,Yes. since 17.1https://forums.juniper.net/t5/Routing/OSPF-routing-issue-with-static-to-same-next-hop/m-p/461851/highlight/true#M19505As the knob implies, FA cannot be P2P and cannot be...

View Article


Re: Can you configure the forward address in Juniper for Type 5 (external) LSAs?

Hey, Thanks for the reply. So in this instance, when you configure this, it seems to send it to the broadcast address (although, in the example you linked, it looks like it would actually set it to the...

View Article


Re: Can you configure the forward address in Juniper for Type 5 (external) LSAs?

Hello,  wrote: So in this instance, when you configure this, it seems to send it to the broadcast address Incorrect. The FA in Type-5 LSA is the same IP@ that is configured as static route' next-hop...

View Article

Re: Firewall Filter using a source-address

I was finally able to test this out and the two term solution has solved my problem until I can get another solution in place thank you. 

View Article

Inline / Static NAT for many /32's...

I have 50+ specific /32 IPs that I need to inline-nat from private to public IPs. How can I add that many into my setup? I'm using an MX480 with two MPC 3D 16x 10GE line cards.  I'm using a service...

View Article

Scale of MPC 3D 16x10GE

Hi fellow enthusiasts, I am seeing memory exhaustion messages for MPC 3D 16x 10GE, I am seeing messages like below: Mar 2 08:47:49  test-re0 fpc0 jnh_partition_ok(13926): jnh_expand_partition failed,...

View Article


Re: Scale of MPC 3D 16x10GE

Hi, I suggest to open a jtac case or engage your local account team to verify your use case First, we need to understand how we are using the router which holds your MPC3. What is size of RIB/FIB? How...

View Article

Re: Scale of MPC 3D 16x10GE

View Article


Re: Scale of MPC 3D 16x10GE

Hi Nexon,There is no memory-enhanced knob on MPCshow jnh 0 pool composition < for greater details on actual userThanksVishal

View Article

L2VC is not comming up b/w juniper and cisco

HI,  i am trying setup  a l2VC (Layer 2 VPN) b/w cisco and juniper but it is not comming up. i have a operational T-LDP session b/w juniper-Cisco. i'm getting encapsulation mismatch error on the below...

View Article


Re: L2VC is not comming up b/w juniper and cisco

Your CE facing interface needs to be CCC encapsulated root@R1> show configuration interfaces em3encapsulation ethernet;   <<<<<<<unit 0 {family mpls;  <<<<<<}...

View Article

Re: L2VC is not comming up b/w juniper and cisco

Hi ,Thanks for your responce.i'm getting below error while setting the encapsulation to CCC. root@R1# show interfaces em3encapsulation ethernet-ccc;unit 0;[edit]root@R1# set interfaces em3 unit 0...

View Article

Re: Scale of MPC 3D 16x10GE

Hi Mengzhe and vlsingh, Thank you for your pointers here, yes you are right that there are a lot of parameters than simply plane number for routes it can hold. I was curious to know this so that I...

View Article
Browsing all 8688 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>