Re: Sharing an ARIN block amongst a couple regional sites
Hi, If the ISPs are different, I believe routing the /25s over the L2 links is the only option, otherwise traffic can be blackholed as mentioned previously. You could leverage the no-export option on...
View ArticleRe: Route Annomaly
Hello,Looks like Your BGP nexthop is resolved via RSVP bypass LSP as below: 118.98.8.108/32 *[RSVP/7/1] 6d 21:20:12, metric 30000> to 118.98.5.126 via ae1.0, label-switched-path...
View ArticleRe: Route Annomaly
Hi, Could you check the ospf cost for interface ae0:show ospf interface ae0.0 detailMaybe you could try looking at why the LSP is bypassing ae0:show rsvp session lsp name LSP:R5.MD.PE.TSEL.1--T.D5.KBL...
View ArticleAdding Bridge Domain VLAN to VPLS
MX10 with trunked interfaces down to a series of EX switches. One of the VLANs needs to be added to a VPLS. I don't have the werewhital to lab this up in a full replication of the production...
View ArticleRe: Route Annomaly
Hello, Yes I can see the nexthop currently resolved via RSVP bypass LSP. The question is why traffic didn't back via ae0?Or its must trigger manually? It has been 4 days in this state. below the...
View ArticleRe: Route Annomaly
Hi, As I know this happened because ofto 118.98.8.108 From: 118.98.9.190, LSPstate: Dn, ActiveRoute: 0 LSPname: LSP:R5.MD.PE.TSEL.1--T.D5.KBL, LSPpath: Primary But the same question is why traffic...
View ArticleRe: Route Annomaly
Hi, You could try resetting the LSP:clear mpls lsp name LSP:R5.MD.PE.TSEL.1--T.D5.KBLCould you also check for the CSPF failed:show rsvp interfaceCheers,Ashvin
View ArticleRe: Route Annomaly
Hi, We do add config with hop-limit. nec-riad@R5.MD.PE-TSEL.1> show system rollback compare 2 0 [edit protocols mpls label-switched-path LSP:R5.MD.PE.TSEL.1--T.D5.KBL primary DEFAULT]+ hop-limit 2;...
View ArticleSSG 140 transparent network between multiple VPN subnets
Moved to ScreenOS Firewalls Forum
View ArticleRe: Route Annomaly
Hi, This has constrained the LSP to 2 hop-limits and the bypass LSP as well possibly.From the topology, I guess there might not be any eligible bypass LSP due to this, hence no backup. You could check...
View Articlemx80 capability
Looking for answer how many IPoE dynamic-vlan subscribers are supported at mx80?We use C-VLAN service model without any IP DEMUX features, so one subscriber use only one inner/outer vlans combination,...
View ArticleRe: mx80 capability
Hi, number of used license you can check with "show system license" command, i think it should be 7 used. With C-VLAN there will be 2 ifl for each subscriber, but even with this you should connect 16k...
View ArticleRate limit in ae interface
Hi all, I have a case: customer with ASN 80 connect with ISP 1 via ae interface and operate dual homed.For more detail: the interface using is ae1 with ae1.1 is above position in figure as well as...
View ArticleRe: Rate limit in ae interface
Hi, Please check below techpub , it may help you.Prefix-Specific Counting and Policing Actions...
View ArticleRe: Rate limit in ae interface
Hi adwivediI think it doesn't work. The link that you send set input into one interface. I draw add information of topology for more detail. I'm wondering whether the solution below is work or not....
View ArticleTotally NSSA area and LDP
Hi, I'm seeking advice and possibly new solution to the issue I'm about to descibe. Attached you can find the topology.Basically in this network we have OSPF as the IGP protocol with two areas -...
View ArticleDHCP Server on MX104?
Hi All, May i know whether i can follow url below to configure MX104 act as DHCP server same as SRX or EX. Do we need license to run dhcp server on MX104....
View ArticleRe: DHCP Server on MX104?
Hello, You can follow below url for the same which is specific to MX routers. http://www.juniper.net/techpubs/en_US/junos15.1/topics/concept/dhcp-extended-dhcp-local-server-overview.html Regards, Rushi
View ArticleRe: Totally NSSA area and LDP
Hello,With JUNOS 16.1, You don't need to inject /32s anymore - LDP uses longest...
View Article