Re: 2 alarms currently active Alarm time Class Description 2016-12-08...
Hi Swati, Seems you have shared "show chassis hardware extensive " however if it is not showing output means you have issue with FEB on slot 3, please try reseating it or replace it.
View ArticleRe: 2 alarms currently active Alarm time Class Description 2016-12-08...
but i wonder 1 thing that i suspect if customer has not used FEB 3 and he has not inserted any FEB then why the error is popping?
View ArticleRe: 2 alarms currently active Alarm time Class Description 2016-12-08...
Hi Swati, Please share "show chassis feb detail " for FEB 3.
View ArticleRe: 2 alarms currently active Alarm time Class Description 2016-12-08...
show chassis feb detail Slot 0 information: State Online Intake temperature 35 degrees C / 95 degrees F Exhaust A temperature 36...
View ArticleRe: 2 alarms currently active Alarm time Class Description 2016-12-08...
Hi Swati, FEB in slot 3 is in "present state" means FEB is present in this slot. If there was no FEB for any slot there will be no output when you issue "show chassis feb detail". When you do "show...
View ArticleRe: 2 alarms currently active Alarm time Class Description 2016-12-08...
sure I will verify this with customer.If customer says it is present then how to go further, does this mean issue with FEB 3 which needs to be replaced or I should try with re-seat of FEB 3.If reseat...
View ArticleRe: 2 alarms currently active Alarm time Class Description 2016-12-08...
see below log messages:-%DAEMON-3-CHASSISD_POWER_CHECK: FPC 2 not powering upchassisd[1539]: %DAEMON-3-CHASSISD_VOLTAGE_SENSOR_INIT: Unable to initialize voltage sensor for FEB 3 (group 7, address...
View ArticleRe: Traffic flatted
looks like you will need to attach a sanitized configuration of the system in order to get substantive help. The log seems to indicate an issue with packets dropped due bad config. So we need to see...
View ArticleRe: 2 alarms currently active Alarm time Class Description 2016-12-08...
Present—FPC is detected by the chassis daemon but either is not supported by the current version of Junos OS or is inserted in the wrong slot. The output also states either Hardware Not Supported or...
View ArticleRe: Advertising routes between two SRX210 directly connected devices
Have you read the article from Rushi?Can you see the rip routes >show route protocol ripCheck if you are actually advertising any rip routes? Verify that Device srxB-1 is sending the expected...
View ArticleRe: 2 alarms currently active Alarm time Class Description 2016-12-08...
Please find the below outputslot 0 information: State Online Temperature 44 degrees C / 111 degrees F Total CPU DRAM 128 MB Start...
View ArticleRe: EVPN: No /32 route for existing MAC adress
Thank you very much for your reply. I have still not resolved the issue.I have only 4 devices (2x MX960 and 2x EX9200) My PE and CE routers configured on each and the same device. I have an interface...
View ArticleRe: EVPN: No /32 route for existing MAC adress
May I know evpn instance and vrf instance configuration?
View ArticleMX104 DHCP relay
Hi, Have issue with a MX104 running junos 13.3 I want to configure a dhcp-helper/relay for a interface. I see that the broadcast-packet is recieved on the MX, but the router will not forward the packet...
View ArticleRe: EVPN: No /32 route for existing MAC adress
Ofcourse. Thanks again for thinking with me! username@CORE01> show configuration routing-instances HOSTING-EVPNinstance-type virtual-switch;vrf-target target:101:1009;protocols { evpn {...
View ArticleClik here to view.
Monitoring Radio between OSPF sites.
Above is a diagram showing an example of how the network performs. Site 1 (Second router from core. Current Management Gateway) ▓▓▓▓▓▓▓@Hera> show configuration | except SECRET-DATA | no-more...
View ArticleRe: Monitoring Radio between OSPF sites.
try to configure bfd for ospf for these links.
View ArticleRe: Queries regarding OSPF and LSP
Sorry for the delay. Thanks for sharing the details. I see few strange things: 1. First of all, I see that secondary path is not defined, it is just having hop-limit. Can we configure a strict hop path...
View ArticleUnderstanding how IBGP/EBGP behaves in JunOS
Hello,I am trying to understand how IBGP and EBGP behave in JunOS and I find that the official documentation is in no way enough to understand what is going on. What surprised me was that everything I...
View Article