Re: Understanding how IBGP/EBGP behaves in JunOS
Hi,Yes, you are almost correct and please find the details on BGP route handling in Junos in a simple words, by default, only active BGP routes are advertised. The rules are as simple as follows:1....
View ArticleRe: 2 alarms currently active Alarm time Class Description 2016-12-08...
Hi Swati, Did you reseat the FEB?
View ArticleRe: Advertising /24 for /25 or longer prefixes
This is what we ended up doing. I was just hoping there was a way to pull the aggregate routes from OSPF.
View ArticleRe: Monitoring Radio between OSPF sites.
Do the radio links provide a layer1/2 connection between the Juniper devices? I also note that you are configuring interfaces with overlapping subnets on the same device facing different directions in...
View ArticleL2circuit with IRB
Hi, I`m trying to close a l2circuit between an MX104 and Cisco ASR903 using l2vpn on cisco... What i trying to do is set IRB into a l2circuit that i can see o ASR903 but the l2circuit dont get UP....
View ArticleRe: L2circuit with IRB
Hi, The configuration does not look correct. You are calling an L3 (irb) interface under l2circuit configuration. Also, the vlan-id and encapsulation is missing. Please refer to following links on how...
View ArticleRe: 2 alarms currently active Alarm time Class Description 2016-12-08...
No,I have not done yet, but will ask the end customer to do so.I hope reseating FEB 3 is not traffic impacting right?
View ArticleEVPN: Traffic flows if L3 interface is available
Hi All, I have an MPLS-EVPN infrastructure with 2x MX960 and 2x EX9200. On 1 device i have an active interface with gateway, on the other 3 the VLAN is extended and the irb interface added to the...
View ArticleRe: MX104 DHCP relay
You had the correct solution! I had forgot to edit the RE-filter. Also, dhcp relay within the VRF did not work. I have added it to forwarding-option, and now it works fine. Thank! set...
View ArticleRe: L2circuit with IRB
Something like that? TESTE { instance-type vpls; vlan-id 99; routing-interface irb.99; protocols { vpls { vpls-id 99; neighbor 10.22.0.13; } }}
View ArticleBGP Newbie - IGP sending wrong next-hop?
Hello Forum members!I've been reading up on routing protocols and trying to learn BGP. Right now the setup described is my own private network and devices across the states (kind relatives that let me...
View ArticleSubscribers not coming online.
A prompt responce will be appretiated, Please refer to the ppp-services logfiles I am getting the following errors: Jan 2 23:59:51.401753 sdbId 44484|sessionDbSetStateTerminated: Session...
View ArticleRe: BGP Newbie - IGP sending wrong next-hop?
I suspect the issue has to do with your VPN interface ip addressing. These virtual tunnel interfaces should be setup as if they were a routed link pair instead of as independent /32 addresses....
View ArticleRe: BGP Newbie - IGP sending wrong next-hop?
Hi Folks,Can you please share this piece of information from both sides of the box,show route 10.0.0.10 extensive show route 10.0.0.11 extensive show route receive-protocol bgp 10.0.0.10 extensive |...
View ArticleRe: EVPN: Traffic flows if L3 interface is available
EVPN ARP entries associated with learned MAC addresses will be listed under the below outputs. show bridge evpn arp-tableshow evpn arp-table
View Articlerouting-options { static { route 0.0.0.0/0 next-hop 111.11.11.1; route...
Trying to redistribute static routes from SRX to the attached OSPF neighbor ex-4200 . Here is an extract of my config below.Bottom line is that it's not working. routing-options { static { route...
View ArticleRe: routing-options { static { route 0.0.0.0/0 next-hop 111.11.11.1; route...
You should just use "set protocols ospf export "OSPF Accept" " - not the network-summary-export option. The OSPF Accept policy should then be changed to include both the prefixes you don't want to...
View ArticleHow to apply local-preference to all routes without a hard reset of EBGP?
Hello, I'm trying to redirect outgoing traffic to my neighboring AS to an IBGP router via local-preference.For this reason I'v created a very simple policy and applied it as an export policy: # show...
View Article