Re: L3 VPN Hub and Spoke
Hi again, I have now tried this in the lab but it seems these examples implies you need to use some routing-protocol between the spoke PE-CE. As mentioned in my initial post I need to use static routes...
View ArticleRe: PEM 0 not OK MX104
spuluka wrote:If they are using DC power supplies this is a known issue on PR 1064039 where the fans do not detect the temperature correctly and fail to cool the power supply causing the shutdown to...
View ArticleRe: PEM 0 not OK MX104
I adjusted them experimentally to prevent the PEM error logs. In the worst case I had to drop the script values by 20 degrees. This was an enclosed rack setup with front to back cooling while the...
View ArticleRe: PEM 0 not OK MX104
Hi Chris, It all depends on adequate air flow and ambient temperature conditions. If you read the PR 1064039, it says following:NOTE: In some cases, we may have to use the script after the upgrade....
View ArticleRe: RE-sampling vs pfe-sampling
Hi, Here are my views regarding your query. RE based sampling limitations:Since RE is handling all the control traffic on the router, we cannot configure very aggresive sampling rate as it will result...
View ArticleRe: Segment Routing ( SPRING ) support
Here is some info on the segment routing aka SPRING(source-packet-routing) for reading: Understanding Source Packet Routing in Networking (SPRING)source-packet-routing-enable (Protocols OSPF) Hope this...
View ArticleRe: EVPN: No /32 route for existing MAC adress
I remember some known issues in 14.2. Could you please open JTAC case?
View ArticleRe: how to set up virtual Juniper lab?
A very good learning byte is available for vMX on ESXi server setup. https://learningportal.juniper.net/juniper/user_activity_info.aspx?id=5853
View ArticleShow interface terse in Juniper
Hi I am new to Juniper. Anyone can explain the below interface? what do these interface mean? or send a link. What is a physical interface? Thank you ABC> show interfaces terseInterface Admin Link...
View ArticleHow to use script in Putty to send command line by line?
Hi In order to send a batch of commands correctly to router, we could use script to send command line by line in Putty. Anyone can give some suggestions how to do that? The below is link for CRT. Do...
View ArticleRe: Show interface terse in Juniper
Hi, Please refer to the below link. Interface Naming Overview [KUDOS PLEASE! If you think I earned it!If this solution worked for you please flag my post as an "Accepted Solution" so others can...
View ArticleRe: Show interface terse in Juniper
cbp0 up up..................> customer backbone port https://www.juniper.net/documentation/en_US/junos13.3/topics/concept/pbb-pip-cbp-interface-understanding.html demux0 up up..............> its...
View ArticleRe: How to use script in Putty to send command line by line?
Hi eesunj, I don't know anything regarding this for Putty, but an alternative solution could be using "load set terminal" instead of just pasting commands in configuration mode. That way commands are...
View ArticleCan't see all bgp route
Hello, i can't recieve all 6 route from all router R1 to R7 on Router R2. Router R1 and R3 on confedration number 65000, R2 and R4 in Confederation number 65001 and R5,R6, R7 in Confederation 65002....
View ArticleRe: How to use script in Putty to send command line by line?
Hi Folks,There are multiple options as well, https://www.juniper.net/techpubs/en_US/junos/topics/task/configuration/junos-software-configuration-file-loading.html
View ArticleRe: How to use script in Putty to send command line by line?
it improve a lot that way, but occassionally it does not work well. It means it still send some error commands.
View ArticleRe: How to use script in Putty to send command line by line?
Try adding crt.sleep <> I used to add 1000's of lines without any issues.
View ArticleRe: Monitoring Radio between OSPF sites.
Any advice here? Is there a way I can have port ge-0/0/5 as native vlan 1700? I want to first add VLAN 1700 to port ge-0/0/5 as tagged. Leaving native untagged. I can then test to see if I can access...
View Article