Re: mx480 alarm
thanks a lot, as your knowledge what happens if i leave the error as is, i'm asking this because the router is fully working now. BRGiulio
View ArticleWhy commands sequence is different in MX960 in two router?
Hi, below are two commands in one MX960 routerset policy-options policy-statement ABC term 100 from policy CDEset policy-options policy-statement CDE term 10 from route-filter 10.10.10.10/24 upto /29...
View ArticleRe: Why commands sequence is different in MX960 in two router?
Hi, What JUNOS you are running in both MX960 ?
View ArticleRe: To configure speed of interface port
Hi, Smicker has a valid question. However, you can follow below techpub document to apply rate limit on an interface. Bandwidth Policers
View ArticleRe: Why commands sequence is different in MX960 in two router?
Thanks for your reply. One is 13.3X1, and other is 12.3X5
View Articlevt inteface numbering
Hi Experts, I am running 16.2R1-S2 and trying to add the vt- interface to flowtap , but I cant seem to add anything apart from port 0 or port 10 i.e vt-x/y/0 or vt-x/y/10 i.e I dont...
View ArticleRe: To configure speed of interface port
I completely missed the OP's rate limit question, that must be the intent.
View ArticleRe: To configure speed of interface port
Dear Smicker,Thanks for your reply, Yes, neighbour (i.e. pc) link are required at 10mb that why i am using (show inerterface interface-name speed) .When i am putting up this command then physical as...
View ArticleRe: Configuring Multihoming on the PE Router for VPLS !
thanks for your answer,But if the primary router lost connection to the core, how the loop can occur ? Because at that sittuation, the others router just communicate with the backup router (now it...
View ArticleRe: vt inteface numbering
HI, Have you included tunnel tunnel-services statement in chassis fpc x pic y ? chassis { fpc 0 { pic 0 { tunnel-services; } }}
View ArticleRe: mx480 alarm
Hi Guilio, I would not recommend to keep the device to continue with a faulty card.This is related to the clocking mechanism and that could have impact n internal processes.
View ArticleRe: To configure speed of interface port
If you are required to form a physical link at 10Mbs then you must hard code the PC side to use 10Mbs as well. Your connection is dropping because one side (PC) is set to auto and the other (router) is...
View ArticleRe: vt inteface numbering
Hi,Yes tunnel-services was configured under chassis at pic level but I couldnt specify port number for the vt interface in the format vt-x/0/z it would default to vt-x/0/0 or vt-x/0/10 ThanksSamit
View ArticleRe: vt inteface numbering
Hello,When you specify a bandwidth of 1g, the port number is always 10. When you specify any other bandwidth, the port number is always...
View ArticleExternal Route Summarization - Type-5 LSA's
Hi All, Need to summarize type-5 LSA's. Tried to do it using area-range command(in ABR and ASBR as well), but result negative. Scenario:MX1(area-0) ----- (area-0) MX2 (area-1) ----- (area-1)MX3 MX3 -...
View Articleset policy-options policy-statement in MX960
Hi Here is a question. The prefix 18.14.10.1/32 is 32 bit. Do you think there is difference between orlonger and exact? Please see the below. set policy-options policy-statement IN_PREFIX_A term 80...
View ArticleWhat command can be used to check vrrp priority value in MX960?
Hi,What command can be used to check vrrp priority value in MX960?We use command "show vrrp brief" or "show vrrp", even "show vrrp summary", but it cannot show the vrrp priotity value.Thank you
View ArticleClik here to view.
Re: Static route issue with j2320 upgraded v9.5
Update.. Completely cleared the config, setup as packet only mode.... But now cannot get routes to go back through the external interface.... I can connect to devices through ge-0/0/1.0 to ge-0/0/0.0...
View ArticleRe: What command can be used to check vrrp priority value in MX960?
Not sure if you have try this? These two commands should provide you the priority value set. show vrrp detail | grep Priority Priority: 110, Advertisement interval: 1, Authentication type: md5 show...
View ArticleVRF Setup
We are looking to create a VRF on our existing EX8200s to have a separate routing instance for Disaster Recovery Test purposes. Our end goal is to simulate a production environment that would not...
View Article