Re: Switch VC Reboot on Commit
Hi, we have the same problem on a couple of VC on the same day, with the same symptom and yes both generate a vmcore.
View ArticleRe: Switch VC Reboot on Commit
HI,It could be due to file corruptions.Could you do a file system check? May need a reinstall in case there are bad blocks.You can do this by running the nand-mediak utilityYou can check the below...
View ArticleRe: Switch VC Reboot on Commit
HI,It could be due to file corruptions.Could you do a file system check? May need a reinstall in case there are bad blocks.You can do this by running the nand-mediak utilityYou can check the below...
View ArticleRe: FBF on QFX5100
I do see counters climbing. One of my concerns is that when I pull the filter off the IRB and commit they are still in effect. What's up with that? I'm trying to get the BYOD section to bypass the...
View ArticleIPv6 BGP Session flapping
Good Evening Community, A couple of days ago one of my providers performed a FW upgrade in their Equipment (unknown if Cisco, JunOs, Etc) and my BGP Peering started flapping like crazy. They stated...
View ArticleRe: IPv6 BGP Session flapping
Hello there,joseek9 wrote: Feb 24 18:27:24 MX480 rpd[8035]: bgp_read_v4_update:10317: NOTIFICATION sent to (IPV6_Peering IP) (External AS ASN): code 3 (Update Message Error) subcode 9 (error with...
View ArticleBRAS interface traffic behavour
Hello All, Observing 50% less egress traffic on downlink interface than uplink interface ingress traffic. Could it be normal behaviour due to b/w policer or something else? Scenario:...
View ArticleRe: CGNAT on MS-MPC Best practice
Hi, After going over the details about deterministic port allocation, i see that the only advantage is that Junos allocated ports When a block-size of 0 is specified, block size is calculated...
View ArticleOSPF calculated metrics are slightly different between ospf anf ospfv3, same...
OSPF 3 appears to get metrics incorrect in a NSSA Correct me if I’m wrong but if the routes are injected in the same place, traverse the same links with the same metrics should the totals cost be...
View ArticleRe: CGNAT on MS-MPC Best practice
Hello there, Mannan wrote: Hi, By not specifying 0 but instead a certain # for block size, how would this be different from sequential port block allocation. There is a slight difference only in...
View ArticleTo configure speed of interface port
Hello ,I have to set the speed of ge port at 10mbps . but when i am doing the configuration of 10m (i.e set interface ge-0/1/1 speed 10m) the link goes down with the neighbor . Please help , how to...
View Articlemx480 alarm
hello, some days ago i received this error: 1 alarms currently activeAlarm time Class Description2017-02-27 20:33:37 UTC Major CB 0 19.44 MHz clock failure in your experience what is the cause? hw...
View ArticleRe: mx480 alarm
Hi gullio23, You can check if the clock is initialised or not by going to shell of re0 with root permission and running the below command;cbc -a | grep CLK I am afraid most of such instances, need a...
View ArticleRe: mx480 alarm
hello ssn, thanks for you fast reply here is the output of the command you gave me: root@MX480-E9-Frame% cbc -a | grep CLK0x004c: DPC_CLK_SEL: 0x000000000x0050: DPC_CLK_DETECT:...
View ArticleRe: mx480 alarm
Hi Giulio,The clock seems to have initialized.So the two options left are;1. Reseat the card and see if that resolves the issue. Make sure there are no bent pins.2. RMA of the card.
View ArticleRe: To configure speed of interface port
Presumably you are setting the port to 10Mbs because that's the link speed the neighbor requires to operate. If the neighbor is working at 1Gbs then why are you even changing it?
View Articletraceroute output
Hi All, Anyone know what the "!<10>" means in the output of this traceroute command? xxx@xxx# run traceroute 194.168.8.100traceroute to 194.168.8.100 (194.168.8.100), 30 hops max, 52 byte packets...
View ArticleRe: traceroute output
Hello there, https://www.freebsd.org/cgi/man.cgi?query=traceroute !<num> ICMP unreachable code <num>.And ICMP type 3 (Type 3 is for Dest.Unreach) code 10 is...
View Article