Re: Why JunosA is Master with lower priority in vrrp?
HelloCould you please share the below: bridge domain config where irb.2 is defined show log messages | match vrrp show vrrp brief Regards
View ArticleRe: Why JunosA is Master with lower priority in vrrp?
HI ! because the master was here first and you configured "no-preempt" which means whoever is the master will not switch over as long as he is active regards alexander
View ArticleRe: Why JunosA is Master with lower priority in vrrp?
Thank you so much. I think you are right though I have not tested it yet. I know cisco has this same issue.
View ArticleCommand "set interfaces irb unit 2 enable"
Hi What does this command mean "set interfaces irb unit 2 enable"?Please see the below. It does not show enable item. Why cannot enter the "enable"? Thank you CCC# set interfaces irb unit 2 ?Possible...
View Articleex4300 - Changed VLAN Members on an Interface, Broke OSPF
EX4300 - 14.1X53-D40.8 Changed some interface VLAN members. [edit interfaces ge-0/0/1 unit 0 family ethernet-switching vlan]- members 230;+ members [ 1-183 185-4094 ]; This caused a flap completly...
View ArticleRe: Command "set interfaces irb unit 2 enable"
Hello, What do you want to achieve?If you have disabled the interface, to enable it again you can execute command: delete interface irb unit 2 disable Regards, Rushi
View ArticleRe: ex4300 - Changed VLAN Members on an Interface, Broke OSPF
Hello, That is strange.Through which vlan you have OSPF adjacency? Regards, Rushi
View ArticleRe: filter based routing
finally i got it woring but only if i add a static default route on inet.0 with another preference. 0.0.0.0/0 *[Static/5] 4w5d 17:10:53> to x.x.x.x via ae0.11 [Static/25] 1d 20:37:05> to x.x.x.x...
View ArticleEtherchannel Issue on EX4200
Hi, We are facing problem since the replacement of EX3200 + JUNOS upgrade activity of EX4200 from 12.3 to 15.1R5.5, such that, etherchannel is not working in case primary link goes down. Under normal...
View ArticleRe: Static route issue with j2320 upgraded v9.5
Correct, in the current configuration the BGP routes will be preferred over the static configuration. Really this comes down to what the desired routing design is and how you want failover to work....
View ArticleRe: VRF Setup
Yes, this can be confusing. With a virtual router routing-instance you are creating an separate and independent routing table and set of interfaces on the device. Thus you can have overlapping...
View ArticleRe: BRAS interface traffic behavour
You can see the actions of the policer using show policier and adding detail to the show interface command.show interfaces ge-1/3/0.1 detail See the verification section of the...
View ArticleRe: ex4300 - Changed VLAN Members on an Interface, Broke OSPF
How exactly are the vlan memberships configured? the compare you post seems to imply that all vlans are deleted and then added by this commit. That would cause a flap for all vlans and of course a...
View ArticleDo you think the route can be sent out?
Hi, Please see below configuration. Can you explain if the route 10.1.128.8/32 can be send out? That also means that other routers can receive the route? Thank you set interfaces lo1 unit 100 family...
View ArticleClik here to view.
Re: Configuring Multihoming on the PE Router for VPLS !
Thanks so much !I understand carefully now !
View ArticleRe: Do you think the route can be sent out?
Hello, Which interfaces are part of routing-instance ABC? Regards, Rushi
View Articlevlan tags in the interfaces and in the VPLS routing instance !
Hello,I have some confusions when i try to understand vlan tag in the interfaces and in the VPLS routing instance.Topology of lab:Customer_switch1 <--trunk--> MX_PE1 <----> (core)...
View Article