Re: Continuous ospf redist events
HiThanks for response and apologies for slow reply on my side.I'm pretty sure there are no duplicate router-ids. All of them are hardcoded and the only way to have duplicates is typo in config. You can...
View ArticleRe: MX not sending SYSLOG to STRM
Just to close the issue out, finally got it working. What I did originally was setup a routing-instance that had the static route to the 192.168 network via the 0/1/9 interface. Then the firewall rule...
View ArticleConfigure EX4200 as a router
Hello guys We have two EX4200 installed with virtual chassis and we want to use it as a router with several LACP aggregations, for example: On the top of our infrastructure we have a router (edge...
View ArticleClik here to view.
Query on the default, default route installed by the Kernel
Hi Guys, Had a quick query that's more out of curiosity than anything. Currently studying between the JNCIA and JNCIS level and it's noted that by default, there is a default route installed by the...
View ArticleQoS scheduler on MX80
Hello forum guys, I would like to implement qos scheduler but I am not very familiar with junos in regards qos config. What I would like to do, it is bacis like this config I would on cisco:...
View ArticleRe: QoS scheduler on MX80
Hi, Maybe you should habve a look on this Day One book "Day One: Junos QoS for IOS Engineers"http://www.juniper.net/us/en/training/jnbooks/day-one/fundamentals-series/junos-qos/ --If this post solves...
View ArticleRe: Configure EX4200 as a router
Hi I was able to figure out the issue with traffic forward. I analised the traffic with tcpdump and the IP address of the VME that was comming. As the both interface: VME interface and the outgoing...
View ArticleL2circuit Frame format
Does anyone have any good links to how the frames are formatted/frame layout of l2circuit connections? IE something that shows inner vlan/outer vlan/mpls header etc? And what order that are in Having...
View ArticleRe: Query on the default, default route installed by the Kernel
if you create your own static default route, the sytem defined entry in the forwarding table is not overridden as you can clearly see from the output show route forwarding-table. Both default entires...
View ArticleClik here to view.
Re: Query on the default, default route installed by the Kernel
I guess this is just by design, like how Local and Direct routes are preferred over all other routes.Thank you
View ArticleConfiguring multiple prepend AS path for BGP
I have multiple AS path to prepend depending on the IP address matched in my prefix list.The idea is to match incoming IP addresses against my prefix list and prepend the AS number accordingly. I have...
View ArticleRe: Configuring multiple prepend AS path for BGP
I assume the two terms you list are part of the prependpolicy applied to the group prependpolicy. When you have multiple terms they are applied in order to the routes on a first match basis. And the...
View ArticleRe: Configuring multiple prepend AS path for BGP
Hey thanks for getting back to me. I am not certain if i can have 2 different prepend function in a single policy function. Am pretty new to L3 routing for Junos. Noted for the default behaviour. I...
View ArticleRe: Configuring multiple prepend AS path for BGP
Yes, you can have two different prepend operations in the same policy. Naturally the terms would need to be written such that hitting they affect different prefixes. A common use case for this would...
View ArticleOSPF Unnumbered interface between Cisco and Juniper
I'm having a problem setting an OSPF point-to-point unnumbered interface between a QFX5100 and a Cisco Nexus 5672. I know all the base parameters are correct... when I switch the interface over to a...
View ArticleRe: OSPF Unnumbered interface between Cisco and Juniper
At which state it stuck at voth sides ? interfaces configured as point-to-point ?
View ArticleRe: OSPF Unnumbered interface between Cisco and Juniper
Hello, Can you share interface & OSPF specific configuration for the related interfaces on QFX and Cisco Nexus? Regards, Rushi
View ArticleRIB,FIB, and PPS (Packet Per second) Maximum capacity on Juniper MX5 can hadled?
Dear All, can anyone help me to get information about MX5 Maximum capacity, because i can get that information from any datasheet on juniper website, information i needed is maximum capacity for :- RIB...
View ArticleRe: OSPF Unnumbered interface between Cisco and Juniper
They are in INIT state. Yes, both side have been configured as point-to-point. From a debug on the Cisco side looking at the hellos it looks like it might be a mask issue.
View Article