The possibility to use multiple peer-unit on Logical-Tunnel Interfade
Hello I have just been investigating the possibility to use multiple peer-unit on Logical-systemI mean that I want to do the following topology and feature, actually is that possible? R1...
View ArticleRe: The possibility to use multiple peer-unit on Logical-Tunnel Interfade
Hi, lt-interfaces are point-to-point interface not multipoint, so you can only setup a full mesh of p2p connections between the three logical routers. Having set this, you might achieve your goals by...
View ArticleRe: The possibility to use multiple peer-unit on Logical-Tunnel Interfade
Thank you for your precious info!, it is very good reference for me.
View ArticleTesting radius server from MX router
I'm just trying to test access to a radius server directly from a MX104 router by doing the simple test below: "test access radius-server 8.8.8.8 user test@test.net password test secret 12345"*...
View ArticleRe: MX40 VPLS port mirror??
Thanks for the reply. See attached config. WinPCAP is installed with Wireshark which makes the NIC promiscuous.
View ArticleQ-in-Q - Unable to send multiple inner tags through single outer VLAN on MX
Hello,I am working with an MX480 connected to a Cisco network. I am trying to send multiple inner vlans through a single outer qinq tunnel interface. Addtionally, I have the inner VLANs terminating...
View ArticleRe: MX40 VPLS port mirror??
The configuration looks very much the same as the one I have been using. However, I found in...
View ArticleRe: Q-in-Q - Unable to send multiple inner tags through single outer VLAN on MX
Try this:ge-2/1/2 { description "--- UPLINK TO TNDM-METR-SW1 G1/5 NNI-TRAFFIC ---"; flexible-vlan-tagging; mtu 9000; encapsulation flexible-ethernet-services; unit 1976 { encapsulation vlan-bridge;...
View ArticleMulticast with TTL of 1 - how to route across subnets - PIM not working
Hello all... I'm pulling my hair out here trying to figure a way to send multicast packets with a TTL of 1 generated by our PBX paging system, over to our other voice subnets. I've opened a case w...
View ArticleRe: Multicast with TTL of 1 - how to route across subnets - PIM not working
Hi Dennis, due to RFC791, every router has to decrement the TTL value. Nothing you can do about this. Having said this, there are two solutions: (a) sent packets with TTL > 1 or (b) setup a layer-2...
View ArticleRe: Q-in-Q - Unable to send multiple inner tags through single outer VLAN on MX
Thanks for the reply, but unfortunatly that didn't fix it. When I add the second inner-vlan the first irb interface shows up/up, but the second one shows up/down.c.anderson@TNDM-T3-EDGE-01# run show...
View ArticleRe: Inter VLAN routing / same subnets and uplink
Sounds like you would have to consider using the security features of vr's and NAT on the router, to be specific double NAT. If you could add the same subnet to each vlan, then how do you suppose arp...
View ArticleRe: Q-in-Q - Unable to send multiple inner tags through single outer VLAN on MX
Okay, maybe I was over-engineering things here... Here is the config I used to get it working:interfaces ge-2/1/2 flexible-vlan-tagging; mtu 9000; encapsulation flexible-ethernet-services; unit 345 {...
View ArticleRe: How to edit permissions to allow show and deny editing under the same...
set system login class CLASS deny-configuration routing-optionstest1@srxF-2# edit routing-options ^permission denied.
View ArticleClik here to view.
Re: Can't route out of the switch on EX2200
Can you add some kudos and mark as resolved
View ArticleRe: Multicast with TTL of 1 - how to route across subnets - PIM not working
Hi !I cannot offer any help on Junos but as you spoke about cisco equipmentCisco IOS has a feature called "Multicast Service Reflection" this allows to reinstate a mutlicast stream with normal TTL To...
View ArticleRe: How to edit permissions to allow show and deny editing under the same...
Hi,Its not working,fisrt of all "deny-configuration" cant configured simultanios with "deny-configuration-regexps" it responce an error:[edit system login class L2-CLASS] 'deny-configuration-regexps'...
View Articlehow to configure DHCP server on MX 960
Hi Guys,i need help on how to set up DHCP server on MX 960 (i have attached "show chassis hardware" output). i tried following this link : Example: Complete DHCP Server...
View ArticleHow to filter ssh access if device is default gateway in a routing instance
Hello all, I need to filter ssh access from servers that i have in different routing instances ( VRFs) when device is a default gateway for them. There are any option to set filter en global...
View ArticleRe: How to filter ssh access if device is default gateway in a routing instance
Hi Fran, Are you looking to filter ssh access to the device from the servers or are you trying to filter ssh access from a routing instance through the device to another routing instance ?
View Article