Re: BFD Best Practices
There is a Feature Inline BFD qualified around 5 years back . We have qualified Single hop Distributed Inline BFD session with below timers 3ms timer with multiplier 3 -- 600 BFD sessions 50 ms timer...
View Article[MX 480] No console access on devices Master RE
Hi all, I'm recently having issues conencting to one of my mx480 routers (Junos: 15.1F6-S2.3) routing engine console port. Trying xxxxx...Connected to xxxxx.Escape character is '^]'. We've swapped...
View ArticleRe: [MX 480] No console access on devices Master RE
Hi, At the console terminal widow, type CTRL Z or CTRL X and try again.Hope you're setting the right serial port...
View ArticleRe: [MX 480] No console access on devices Master RE
Hi karand, We did set the console values correctly. As mentioed previously we swapped the consoles between the REs and we could reach RE1 without issues, moreover we did manage to connect to RE1 also...
View ArticleRe: Traffic engineering question
Use MPLS CoS (EXP) to prioritize traffic within an LSP.https://www.juniper.net/documentation/en_US/junos/topics/usage-guidelines/mpls-configuring-class-of-service-for-mpls-lsps.html
View ArticleRe: Traffic engineering question
Also, Refer to Differentiated Services (DiffServ)-aware traffic engineering provides a way to guarantee a specified level of service/bandwithd:...
View ArticleRe: what is the difference between lo0.50 and lo0 unit 50?
It’s a same thing.You can either use lo0.50 or lo0 unit 50 while configuring the interface.Unit 50 is represented by lo0.50.
View ArticleRe: what is the difference between lo0.50 and lo0 unit 50?
Thanks, King. Is it same as irb unit 50. If not what is the difference between them? what is the difference between lo0.50 and lo0 unit 50? Regards,Remington, J
View ArticleRe: what is the difference between lo0.50 and lo0 unit 50?
It applies to all the interfaces.The unit interface is represented by .xx interface name.You can either use irb.50 or interface irb unit 50.
View ArticleRe: [MX 480] No console access on devices Master RE
Confirm that the console port is not disabled undersystem ports console
View ArticleSRX220 Routing Question
We are using Juniper SSG20's right now as our edge firewall and are using SRX220's and 300's for use with just Wi-Fi. The SRX will handle DHCP and DNS and all the Wifi subnets on terminated on the SRX....
View ArticleConfigure TDMOIP
Hello Members, I have to configure TDMOIP . But when we see the guide, I got that for L2Circuit(pseudowires), MPLS is mandatory. SO, How to create a pseudowires without MPLS for transfrer the TDM...
View ArticleRe: SRX220 Routing Question
Will need more info about the setup. If possible, you may paste a flow diagram along with dummy ip addresses. anyways. following is something i understood. 1. You seem to be having Internet links on...
View ArticleRe: Configure TDMOIP
Hello,JUNOS calls TDM over IP "SATOP".You will need specific handware to do that:1/ ACX1K or ACX2K https://www.juniper.net/documentation/en_US/junos/topics/concept/e1-t1-satop-emulation.html 2/...
View ArticleRoute aggregation for eBGP peers
Hi. Could a kind soul confirm if mx80s will advertise an aggregate prefix by default while only learning some prefixes within that aggregate block via ospf? For example, I would like to advertise...
View ArticleClik here to view.
VPLS failing with routing-engine failover
Hi everybody. I have a question and I am looking for a solution. PE1 and PE2 are two different locations, P3 and P4 are in the same location. I have the following topology, where PE1-PE2, PE1-P3 and...
View ArticleRe: Route aggregation for eBGP peers
In order to advertise a route it must be in your routing table. Not just contributing routes, but the actual aggregate route you want to advertise. Both methods you note will work. If the aggregate...
View ArticleRe: VPLS failing with routing-engine failover
I believe you use BGP for VPLS signalling, have you configured GRES &...
View ArticleRe: VPLS failing with routing-engine failover
Do you have both GRES and NSR configured already? https://www.juniper.net/documentation/en_US/junos/topics/task/configuration/gres-configuring.html...
View Article