ptp master unsupported MX80
Hello forum guys, I configured ptp master in ordinary mode on MX80: run show configuration protocols ptp clock-mode ordinary; unicast-negotiation; master { interface ae1.903 { unicast-mode {...
View ArticleClik here to view.
VRRP Configuration
Hi, i have QFX3500 (non ELS) dan QFX5100 (with ELS), i want to config VRRP at that device.with this topology...what the best recommendation VRRP Configuration? Thanks,
View ArticleRe: VRRP Configuration
The VRRP configuration is not different between non-ELS and ELS, except the VLAN l3-interface naming where it is applied: vlan.X for non-ELS and irb.X for ELS. You can use this guide for VRRP...
View ArticleRe: VRRP Configuration
from that topology, what minimum requirement system and device to perform VRRP?wether, need equals the device requirement between QFX3500 and QFX5100?
View ArticleRe: ptp master unsupported MX80
There are two flavours of MX80 chassis, MX80-AC and MX80-P-AC. For PTP support, you need the later one. Do you have a MX80-P model? Cheers,Carsten
View ArticleRe: ptp master unsupported MX80
hm - how can I check it? run show chassis hardware Hardware inventory: Item Version Part number Serial number Description Chassis G3894 MX80 Midplane REV 09 711-031594 CABD2043 MX80 PEM 0 Rev 05...
View ArticleRe: VRRP Configuration
With respect to only configuring VRRP, on any Juniper platform you can configure that. But you should do some research on the scale/the throughput you need for your network before you can choose the...
View ArticleRe: ptp master unsupported MX80
http://www.juniper.net/documentation/en_US/release-independent/junos/topics/concept/mx5-mx10-mx40-mx80-router-models.html show chassis hardware should show MX80-P-AC or MX80-P-DC for 1588 supported...
View ArticleClik here to view.
BGP question for VC EX4300 switch
Hi. I will be replacing an old set of switches with a pair ex4300s in VC with AFL and EFL . This switches connectivity to the rest of the network is via two circuits running BGP to layer3 switch...
View ArticleRe: ptp master unsupported MX80
Hi akushner, So, from obove output show chasis hardware, as far as I can see, this is chasis MX80 AC but without ptp support. I understand, if ptp was supported, I would have MX80-P-AC output.
View ArticleRe: VRRP Configuration
Base on my topology, which is i must use configuring VRRP using unicast or multicast?Because base on...
View ArticleRe: BGP question for VC EX4300 switch
Yes, you can use this configuration with dual BGP peers on the switch. In this setup you would have a port on each switch of the VC so you have local hardware redundancy as well.
View ArticleRe: QinQ encapsulation on l2vpn
Hello,It is not clear what You are actually trying to achieve here.First, based on Your config You are pushing S-TAG on output from xe-1/0/0.11 and xe-1/0/0.12 set interfaces xe-1/0/0 unit 11 vlan-id...
View ArticleRe: QinQ encapsulation on l2vpn
Hello, Yes, I agree with you that the push should be removed to achieve my goal. That would solve the outgoing packet direction problem.However when an incoming packet comes in on the interface with...
View ArticleRe: QinQ encapsulation on l2vpn
Hello, pete_j wrote:Hello, when an incoming packet comes in on the interface with C-TAG 100-110 it should be directed to xe-1/0/0 unit 11 and 200-210 should be enclosed in unit 12 (as each 11 and 12...
View ArticleMC-LAG active/standby with martini PW's
Hi,I have been looking for a service provider best practice on how to implement MC-LAG active/stanby mode towards a customer's central site in combination with martini tunnels from remote sites...
View ArticleACX routers - chassis cluster?
A simple question for which I cannot find a clear answer... Can I configure a chassis cluster with a pair of ACX routers?Thanks!
View ArticleRe: ACX routers - chassis cluster?
Chassis cluster is the defintion for a SRX firewall cluster. For switches it would be virtual chasis and MC-LAG on eg. MX router. If the ACX supported something like this I would expect it to be...
View ArticleRe: MC-LAG active/standby with martini PW's
From you diagram it looks like you are connected and MC Lag to two separate CE devices so I see two possiblilities and both present issues you note. If the two devices are separate you are connection a...
View ArticleRe: ACX routers - chassis cluster?
The ACX is primarily an MPLS edge and aggregation node. This does not support virtual chassis which is what the MX series devices use for clustering. Chassis cluster is SRX only. There are some High...
View Article